background image

»

 INSTALLATION INSTRUCTIONS 

/ OCTO & OCTO+

proswell.fr

CAUTION:

 This type of configuration must be protected by one of the four safety systems that comply with French 

safety standards concerning safety of in-ground pools; safety barrier, alarm, safety cover or a shelter.    

The decree no. 2003-1389 dated 31/12/2003 renders it mandatory for clients of pools installed after the 1st of January 

to have the pool fitted with a system to prevent drowning before it is filled with water. Said system must comply with 

either the French safety standards, or with those standards, technical specifications or manufacturing procedures set 

out in the regulations of a member state of the European Community or another state party to the Agreement on the 

European Economic Area, providing for an equivalent level of safety.

These provisions apply to open air pools that are partially or fully in-ground. 

Below, we suggest implementation configurations that show basic recommendations for non-humid ground. You should 

adapt these to your installation, notably, in humid areas (stagnant water, water source, zone subject to flooding, etc.) a 

sump drain pump may be required for efficient drainage.

In any case, the drainage system must be adequate to prevent the stagnation of water that could cause the wood to rot. 

We recommend that you follow the installation instructions to the letter; failure to abide by these instructions will render 

the usual guarantees null and void.  

Should you have any questions, and to ensure a quality installation, do not hesitate to contact a specialist.te.

>>                 

INSTALLATION OF PARTIALLY IN-GROUND OR IN-GROUND 

POOLS

>>                 

EXCAVATION

>>                 

RELIEF WELL

The Delta MS membrane allows ventilation of the wooden 

pool structure. This is necessary to prevent rotting of the 

wood. 

 

Anti-root or 

felt

Undisturbed 

ground

Peripheral 

drain

Drainage 

gravel

Stabilised, levelling course

Waterproofing 

membrane

Concrete slab, min. 

depth : 150 mn

Wooden structure

Geotextile felt

Ground

Relief well

Crushed 

gravel

Peripheral drain

Concrete slab

Delta MS

22

Summary of Contents for ProSwell Weva octo +460

































Reviews: