background image

Jetzt Angebot anfordern auf www.poolseller.de

»

 NOTICE DE MONTAGE

 / OCTO & OCTO +

65

77

78

80

Note the distribution of the various modules constituting the coping on the drawing. Arrange them on the coping 

support brackets taking care to orient them with the finely grooved surface facing upwards. Make sure that the elements 

are correctly and evenly positioned around the entire periphery of the pool. Adjust them if necessary.

The coping elements are 28.5cm wide. The coping hinge, that allows access to the skimmer, requires installation of 

the stainless steel pivots (bag ref 350135 maintenance kit). Fit them into the ends of the central plank then extend  

with the coping end piece elements. To allow the hinge to function correctly, the central plank should not be screwed 

down. Note the correct position of the coping with respect to the liner locking track in the drawing.  Check the coping 

assembly for symmetry and correct if necessary. Fix the modules (except the hinged module over the skimmer) to the 

metallic anchoring plates on the coping support brackets from underneath using roofing screws (bag G). Pre-drill first. 

POOLS FITTED WITH EXOTIC WOOD COPING

>>                

 FITTING THE COPING TO OCTO POOLS

79

IMPORTANT ! Your pool comes with a dechlorinator that removes chlorine from pool back wash water. By installing 

this product, you can recycle back wash water from your pool to water the garden, wash the car, etc. Refer to the 

installation and operating instructions enclosed with the dechlorinator.

- Put the 6-way valve to BACKWASH.
- Turn the pump on.
- Observe the colour of the water in the turbidity sight glass. 
  CAUTION a few seconds will elapse before cleaning begins (water becomes cloudy)
- As soon as the water runs clear, stop the pump.
- Put the 6-way valve to RINSE.
- Switch the pump on for 20 to 30 seconds, to remove impurities and settle the sand.
- Stop the pump.
- Turn the 6-way valve to FILTRATION

- Switch the pump on.

After a back wash, the pressure in the filter should drop back down to the nominal pressure.

>>                 >>                 

COMMISSIONING & OPERATING THE FILTER SYSTEM (contd)

»

 INSTALLATION INSTRUCTIONS

  / OCTO & OCTO +

Jetzt Angebot anfordern auf www.poolseller.de

Summary of Contents for Piscines Bois ODYSSEA 640 BF Ht 146









































Reviews: