Prochem LEGEND GT Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 137

background image

16

Installation

Waste Tank To Console Connection

NOTE: Before connecting any hoses to the waste
tanks, make certain the hose clamps are on each
hose.

1.

Connect the section of 2-7/8" I.D. internal vac hose
between the 2-7/8" dia. vac outlet tube on the
waste tank and the vacuum pump relief valve on
the console. It may be necessary to cut this hose
to fit. Tighten the hose clamps.

2.

Connect the 2" I.D. waste removal hose to the 2"
dia. tube at the bottom corner of the waste tank.
Cut to desired length. Install brass ball valve on
other end.

3.

Connect 2-1/2" I.D. hose between waste tank
vacuum inlet (upper right of waste tank) and
vacuum inlet on lower side panel of console.

4.

Connect the 3/16" blue hose from the water box to
the lower flare fitting (angled downward) on the
waste tank.

5.

Run the 5/8" water box overflow hose through the
van floor. Prior to drilling through the van floor,
ensure that no damage will occur in drilling area.
Ensure that you are in compliance with all local
environmental laws.

6.

Connect the console engine shut-off cord to the
waste tank level sensor cord.

7.

Connect the 3/16" blue hose from the solution
temperature control valve to the other flare fitting
(angled downward) on the waste tank.

Fire Extinguisher

We recommend that a fire extinguisher, preferably
rated for A, B, & C type fires, be installed inside the
vehicle.

Fuel Pump Assembly Installation

Before drilling the fuel line holes in the vehicle
floor, make certain that when drilling you will not do
any damage to the fuel tank(s), fuel lines, brake
lines, heat shields, or any other vital component
which might affect the operation or safety of the
vehicle.

Do not mount this assembly, any hoses or compo-
nents near the catalytic converter, exhaust, or any
areas of high temperature. Avoid any contact with
moving parts, areas of high temperature, brake
lines, fuel lines, muffler, catalytic converter, or
sharp objects.

1.

Determine the position where the fuel pump
assembly will be mounted. Check to ensure that
the power cord length will support the mounting
location. The pump should be mounted as low as
possible and still be protected by the frame from
road hazards.

Mount the fuel pump with the

discharge side of the pump higher than the
suction side to eliminate the possibility of
trapped air in the pump.

Additional mounting

holes are provided to allow for different mounting
options.

2.

Drill a 5/8" (.625) diameter hole in the vehicle floor
for routing the fuel pump power cord to the truck-
mount console. Check to ensure that the cord
length will support the location of the hole.

3.

Route the power cord and install the hole grommet.

4.

Do not connect the power cord to the truckmount
console wiring harness until installation is
complete.

86313050 LEGEND GT

«
...
16
17
18
19
20
...
»

Summary of Contents for LEGEND GT










































































































































Reviews:

No comments

Related manuals for LEGEND GT

Brand: VAPamore Pages: 14

U90-P1 Series POWER1

Brand: Vax Pages: 8

U84-AL-Pe AirLift

Brand: Vax Pages: 20

Brand: White and Brown Pages: 16

Thunderbolt FM239K

Brand: Fantom Pages: 12

Brand: Bissell Pages: 12

Brand: Dirt Devil Pages: 8

Silence Force Extreme RO 5823.11

Brand: Rowenta Pages: 80

097H Speedy Plus

Brand: Monster Pages: 14

Brand: UFESA Pages: 36

Dynamo Cordless 21.6V

Brand: Vax Pages: 16

Brand: VOLTA Pages: 5

Brand: Cleanfix Pages: 2

Brand: Vax Pages: 8

Brand: cecotec Pages: 64

Brand: arovec Pages: 24

Brand: Scarlett Pages: 36

Brand: Zhermack Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands