Proceq Resipod Family Operating Instructions Manual Download Page 17

17

© 2017 Proceq SA

6 Units, Parts and Accessories

Part No.

Description

381 10 000

Resipod, 50mm probe spacing, test strip, foam contact pads, charger with USB-

cable, software, carrying strap, documentation and case .

381 20 000

Resipod, 38mm (1 .5”) probe spacing, test strip, foam contact pads, charger with 

USB-cable, software, carrying strap, documentation and case .

381 30 000

Resipod Bulk Resistivity, 50mm probe spacing, test strip, foam contact pads, 

charger with USB-cable, software, carrying strap, documentation and case, 

Bulk Resistivity Accessory .

381 40 000

Resipod Bulk Resistivity, 38mm (1 .5”) probe spacing, test strip, foam contact 

pads, charger with USB-cable, software, carrying strap, documentation and 

case, Bulk Resistivity Accessory .

381 50 000

Resipod Geometric, 50mm probe spacing, test strip, foam contact pads, char-

ger with USB-cable, software, carrying strap, documentation and case, Resipod 

Geometric Accessory .

381 60 000

Resipod Geometric, 38mm probe spacing, test strip, foam contact pads, 
charger with USB-cable, software, carrying strap, documentation and case, 
Resipod Geometric Accessory .

Parts and Accessories

Description

381 01 088

Bulk Resistivity Accessory

381 01 098

Resipod Geometric Accessory

381 01 094

Variable Spacing Probe

381 01 089

Resipod Stand

381 01 043 S

Set of replacement foam contact pads (5x4)

381 01 092 S

Bulk resistivity contact pads . Set of 10 pieces

381 01 038

Test strip

381 01 031

Inner contact cap (See note below)

381 01 041

Outer contact cap (See note below)

381 01 033

Contact complete (See note below)

381 01 036

Contact spring

381 01 014

USB cover

381 01 070

Key for USB port

391 80 110

Carrying strap

 

To replace one of the inner contacts requires parts 381 01 031, 381 01 033 and 381 01 036 .
To replace one of the outer contacts requires parts 381 01 041, 381 01 033 and 381 01 036 .

7 Technical Specifications

Measurement range:

1k

Ω

cm - ca . 1000 k

Ω

cm (dependent on probe spacing) 

Resistance measurement accuracy:

Nominal current 200µA

±0 .2 k

Ω

cm or ±1% (whichever is greater)

Nominal current 50µA

±0 .3 k

Ω

cm or ±2% (whichever is greater)

Nominal current <50µA

±2 k

Ω

cm or ±5% (whichever is greater)

Frequency

40 Hz

Memory

Non volatile, ca . 500 measured values

Power Supply

>50 hours autonomy

Charger connection

USB type B, (5V, 100mA)

Dimensions

197 x 53 x 69 .7 mm (7 .8 x 2 .1 x 2 .7 inch)

Weight

318 g (11 .2 oz)

Operating temperature

0° to 50°C (32° to 122°F)

Storage temperature

-10° to 70°C (14° to 158°F)

Summary of Contents for Resipod Family





























Reviews: