probst VM-301-KJ-PAVERMAX, Operating Instructions Manual

Page: 33 / 161

Maintenance and care 32 / 38
51500020 / 51500023 V5 GB
7 Clean air filter (renew when strong pollution) ①
⚫ ⚫ ⚫
8 Exchange air filter
⚫
9 Clean fuel filter ① / ③
⚫ ⚫
10 Exchange fuel pre-filter ① / ③
⚫ ⚫
11 Checking the fuel pipe and clamp fitting
⚫ ⚫ ⚫
12 Checking the fan belt tension (on fan wheel)
⚫ ⚫
13 Exchange fan belt (on fan wheel) ① / ④
14 Checking the radiator hose and clamp fitting (if necessary renew)
⚫ ⚫
15 Remove sediments from fuel tank ④
16 Checking the cooling ribs for pollution
⚫ ⚫
17 Checking the electric wiring for loose connections
⚫ ⚫ ⚫ ⚫
18 Checking the exhaust system and clamp fitting
⚫ ⚫
19 Recharge the battery (if necessary renew)
⚫ ⚫
20 Checking the cooling water level (if necessary refill)
⚫ ⚫ ⚫ ⚫ ⚫
21 Exchange cooling water including antifreeze (~ 4 l)
⚫
22 Checking the antifreeze in cooling water (before each frost period)
⚫ ⚫
23 Checking the opening pressure of radiator cover lid
⚫ ⚫
24 Checking the jet opening pressure
⚫
25 Checking the compression pressure
⚫
26 Checking the hydraulic hoses on leakages (retighten connections)
⚫
②
⚫ ⚫
27 Checking the function of instruments and operating elements
⚫ ⚫ ⚫
28 Checking the VM for defective, distorted construction units and abnormal noises
⚫ ⚫ ⚫
29 Retighten all screws and nuts, replace missing screw connections
⚫ ⚫ ⚫
30 Checking the tyre pressure (front 2,5 bar/36 psi, rear 2,2 bar/32 psi)
⚫ ⚫ ⚫
31 Lubricate according to lubrication chart
⚫ ⚫ ⚫
32 Check ball joint on strength (135 Nm)
⚫ ⚫ ⚫
33 Check carrying construction units on cracks (axles, chassis, swiveljoint, steering
rod)
⚫ ⚫ ⚫
34 Retighten all wheel nuts (130 Nm)
⚫ ⚫ ⚫
35 Checking the hand brake (if necessary readjust 3-4 teeth)
⚫ ⚫ ⚫
36 Checking the wheel bearing and axle bearing (if necessary readjust)
⚫
37 Check steering clearance (if necessary renew spherical head or tie rod ①
⚫
38 Checking the dynamo machine
⚫
39 Adjustment valve clearance of tilting lever (0,15 mm)
⚫
To disconnect the electric system from the battery, the main switch must be activated at the VM-301-PAVERMAX at the right hand side.
At about the same place, there is a lock to be pulled out to unlock the cover, where the seat is fixed to.
At welding the battery main switch must be switched off general. Otherwise the electronic could be damaged!
Daily check before starting: Engine oil level, coolant, antifreeze, mater level hydraulic fluid level, battery, "V" belt tension.
② and additionally exchange every 50 hours ③ exchange all 400 hours ④ exchange all 500 hours