PROBOIL PROBOIL.4E User'S Installation Manual Download | Manualshive

Page: 4 / 44

background image

PROBOIL.4E user & installation guide v1d

4

⚠

WARNING

:

Never use this appliance when your judgement or coordination may be impaired by

the use of either alcohol or drugs.

⚠

WARNING

:

Do not open or disconnect the tank until the tank has cooled to a safe temperature.

⚠

WARNING

:

If the appliance is to be handed over to someone else for use, all documentation

and information should also be given.

⚠

WARNING

:

This appliance must be installed respecting local plumbing and electrical regulations.

⚠

WARNING

:

This appliance must use only genuine parts, accessories and sundry consumables.

⚠

WARNING

:

Packaging materials can be dangerous to children and animals; ensure they are

disposed of safely and correctly according to local laws.

1.1.2

Electrical safety:

⚠

WARNING

:

Do not use this appliance if you suspect it or any of its cables or hoses are damaged

or kinked in any way, or is performing differently from how you would expect. Never use any
appliance with a damaged mains power lead. In the event of any suspected problem you should
immediately cease usage, isolate the water supply, disconnect the power and contact the service
agent noted on the top of the boiler.

⚠

WARNING

:

This appliance must be disconnected from the power during installation,

maintenance or cleaning.

⚠

WARNING

:

Only use the supplied power cable and connect it directly to the power outlet rather

than an extension power outlet.

⚠

WARNING

:

The appliance must be installed so that it can be disconnected from the mains

power supply and the outlet socket must be accessible at all time.

⚠

WARNING

:

This appliance must be connected to a grounded / earthed power outlet only.

⚠

WARNING

:

This appliance must be installed respecting local plumbing and electrical regulations.

«
...
2
3
4
5
6
...
»

Summary of Contents for PROBOIL.4E













































Reviews:

No comments

Related manuals for PROBOIL.4E

Brand: CleaverBrooks Pages: 314

Brand: Viadrus Pages: 48

Brand: Varmebaronen Pages: 16

Brand: Argo Pages: 24

Brand: Nibe Pages: 12

Brand: Hoberg Pages: 90

Brand: ATTACK Pages: 60

ATTACK DPX 25 COMBI Pellet

Brand: ATTACK Pages: 100

Brand: Embassy Pages: 68

HERCULES Condensing ABT 32 2 I

Brand: Immergas Pages: 60

Brand: Nature's Comfort Pages: 30

Brand: Worcester Pages: 20

F85H Fire Coil 85 200

Brand: Natco Pages: 44

Brand: Viessmann Pages: 36

Brand: Daikin Pages: 16

Brand: ICI Caldaie Pages: 28

Domitop HF 24-30 E

Brand: Ferroli Pages: 40

Brand: Radiant Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands