background image

3

EN

Contents

Impulse

 17

Recommended Tools and Materials

•  Needle nose pliers
•  Paper towel
•  Rubbing alcohol
•  Temporary threadlock

•  Nut driver: 5.5mm
•  Phillips screwdriver: #1
•  Hex wrench: 2.5mm
•  Clear tape (DYNM0102)
•  Pro Boat

®

 Marine Grease and Gun (PRB0100)

Introduction

Pro Boat

®

 RC models look as good as they perform. Our boats, which include everything from scale sailboats to  

fully licensed powerboats, exceed expectations and provide years of radio control fun and excitement. Whether your 

passion leads you towards the pure serenity of sailing or the all-out speed of a Deep-V, Pro Boat models fit your taste, 

budget and lifestyle. You can count on us to be available any time you need help—the brand is backed by Horizon 

Hobby, one of the world’s largest distributors of hobby-grade RC products. The Pro Boat brand will help you turn  

your boating passion into a reality, whether you’re new to the hobby or an old pro.
Please read this manual for operation and maintenance instructions.

Register your boat online at www.proboatmodels.com.

Product Inspection

Carefully remove the boat and radio transmitter from the box. Inspect the boat for damage.  

If you find damage is present, please contact the retailer where you purchased your boat.

Miss GEICO 17

Impulse 17 • Miss GEICO 17

Summary of Contents for Impulse 17















Reviews: