2
3
Save these instructions. For your safety,
read, understand, and follow the information
provided with and on this jack. The owner
and operator of this equipment shall have an
understanding of this jack and safe operating
procedures before attempting to use. The
owner and operator shall be aware that use
and repair of this product may require spe-
cial skills and knowledge. Instructions and
safety information shall be conveyed in the
operator's native language before use of this
jack is authorized. If any doubt exists as to
the safe and proper use of this jack, remove
from service immediately. Inspect before
each use. Do not use if broken, bent,
cracked, or damaged parts (including labels)
are noted. Any jack that appears damaged
in any way, operates abnormally or is
missing parts, shall be removed from service
immediately. If the jack has been or sus-
pected to have been subjected to a shock
load (a load dropped suddenly, unexpectedly
upon it), immediately discontinue use until
jack has been checked by a factory
authorized service center. It is recommended
that an annual inspection be done by qualified
personnel. Labels and Owner's Manuals are
available from manufacturer (see Replace-
ment Parts, page 5).
PRODUCT DESCRIPTION
Pro-Lift Speedy Lift Floor Jacks are designed
to lift, but not sustain, rated capacity loads. It
is designed to be used in conjunction with
jack stands. Pro-Lift Speedy Lift Floor Jack
have a unique feature which provide fast, no
load lifts to the jacking point. Intended use:
To lift one axle of a vehicle for the purpose of
service and/or repair of vehicle components.
After lifting, loads must be immediately sup-
ported by appropriately rated jack stands.
Check with vehicle owner's manual for
proper lift points.
BEFORE USE
1. Verify that the product and the application
are compatible, if in doubt call Pro-Lift
Customer Support @ (816) 891-6390.
2. Before using this product, read the
owner's manual completely and familiar-
ize yourself thoroughly with the product,
its components and recognize the haz-
ards associated with its use.
3. Using the stamped end of the provided
handle, engage and turn the release valve
counterclockwise no more than 1/2 full
turns from a fully closed position.
4. With saddle fully lowered, locate and re-
move the oil filler plug. Insert the handle
into the handle sleeve, then pump 6 to 8
full strokes. This will help release any
pressurized air which may be trapped
within the reservoir. Oil level should be
~3/16" above the inner cylinder as seen
from the oil filler plug hole. Reinstall the
oil filler plug.
5. Check to ensure that jack rolls freely (if
so equipped) and that the pump operates
smoothly before putting into service. Re-
place worn or damaged parts and as-
semblies with factory Authorized Re-
placement Parts only (See Replacement
Parts Section). Lubricate as instructed
in Maintenance Section.
Figure 1 - Typical speedy lift floor jack
Nomenclature
OPERATION
Lifting (refer to Fig 1, Page 2)
1. Place vehicle in park, with emergency
brake on and wheels securely chocked
to prevent inadvertent vehicle movement.
2. Locate and close release valve by turning
handle clockwise until firm resistance is
felt to further thread engagement. Cen-
ter jack saddle under lift point.
3. Verify lift point, insert handle into handle
sleeve and pump to contact lift point. To
lift, pump handle until load reaches de-
sired height.
4. Transfer the load immediately to appro-
priately rated jack stands.
Lowering
1. Raise load high enough to clear the jack
stands, then carefully remove jack
stands (always used in pairs).
2. Slowly turn the handle counterclockwise,
but no more than 1/2 turn. If the load fails
to lower:
a. Use another jack to raise the vehicle
high enough to reinstall jack stands.
b. Remove the affected jack and then the
stands.
c. Using the other jack, lower the load by
turning the operating handle counter-
clockwise, but no more than 1/2 turn.
3. After removing jack from under the load,
push saddle down to reduce ram expo-
sure to rust and contamination.
ASSEMBLY
Little, if any, assembly is required of this
jack. Familiarize yourself with the illustra-
tions in the owner's manual. Know your
jack and how it operates before attempt-
ing to use.
! SAFETY MESSAGE !
Be sure all tools and personnel are clear
before lowering load. No alterations shall
be made to this device. Only attachments
and/or adapters supplied by the manufac-
turer shall be used. Lift only on areas of
the vehicle as specified by the vehicle
manufacturer.
handle
front
wheel
saddle
handle
sleeve
lifting arm
oil filler plug
rear
caster
release
valve
handle grip
engage release
valve w/ this end
cover plate
(remove to
access oil
filler plug)
Study, understand, and follow all
instructions provided with and on this
device. Do not exceed rated capacity.
This is a lifting device only. After lifting,
immediately transfer the load to appro-
priately rated vehicle stands. Never work
on, under, or around a load supported by
this device. Use only on hard, level
surfaces capable of sustaining rated
capacity loads. Do not move or dolly loads
with this device. Failure to heed these
markings may result in personal injury
and/or property damage.
!
WARNING
• Leer, comprender, y seguir las
instrucciónes antes de utilizar el aparato.
• El manual de instrucciónes y la
información de seguridad deben estar
comunicado en lengua del operador
antes del uso.
• No seguir estas indicaciónes puede
causar daños personales o materiales.
ATENCIÓN
!
