19
2
How To Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Trouble-shooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Weight Resistance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached in the centre of
this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before
beginning assembly.
Table of Contents
How to Order Replacement Parts
TIGHTENING THE CABLES
Woven cable, the type of cable used on the training sys-
tem, can stretch slightly when it is first used. If there is
slack in the Cables before resistance is felt, the Cables
should be tightened.
To tighten the Cables, insert the Weight Pin (39) between
the third and the fourth Weight, counting from the top.
See “Changing the Weight Setting” on page 17 for
instructions on moving the Weight Pin.
Loosen the 1/2” Plain Nut (68) securing the bolt at the
end of the High Cable (73). Tighten the bolt a couple of
turns into the Weight Tube (36) until the Cables feel
tighter. Tighten the Plain Nut to prevent the bolt from turn-
ing.
Note: This drawing shows the Shroud removed for clarity.
The Shroud does not have to be removed to tighten the
Cables.
Additional slack can be removed by moving the lower of
the two Pulleys (35) attached to the Pulley Plates (31) to
one of the other adjustment holes in the Pulley Plates. To
do this, remove the 3/8” x 1 3/4” Bolt (60), Cable Trap
(44) and 3/8” Nylon Jamnut (63). Move the Pulley and re-
attach it with the Bolt, Cable Trap and Locknut. Make
sure the Low Cable (72) is in the groove of the Pulley
and that the Cable Trap is positioned as shown.
Note: If a Cable tends to slip off the Pulleys often, the
Cable may have become twisted. Remove the Cable
and re-install it.
If the Cables need to be replaced, see ORDERING
REPLACEMENT PARTS on page 2 of this manual.
36
68
Bolt
73
39
60
35
63
72
31
44
Trouble-shooting and Maintenance
To order replacement parts, contact the ICON Health & Fitness Ltd. office, or write:
ICON Health & Fitness Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
Fax: 0113-2411120
When ordering parts, please be prepared to give the following information:
• The MODEL NUMBER OF THE PRODUCT (PFEMSY75000)
• The NAME OF THE PRODUCT (PROFORM
®
825 training system)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST and the EXPLODED DRAWING
attached in the centre of this manual).
Tel.: Country Code: 0345-08900
Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. The
training system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
PROFORM
®
is a registered trademark of ICON Health & Fitness, Inc.
