background image

3

1.  It is the responsibility of the owner to ensure 

that all users of the rack are adequately 

informed of all precautions.

2.  Keep children under age 16 and pets away 

from the weight bench at all times.

3.  Consult your health care provider before 

beginning any exercise program. This is 

especially important for persons over age 

35 or persons with pre-existing health 

problems.

4.  Consult your health care provider before 

beginning or continuing any exercise pro-

gram during pregnancy. Use the weight 

bench only as authorized by your health care 

provider. 

5.  The rack is not intended for use by persons 

with reduced physical, sensory, or mental 

capabilities or lack of experience and knowl-

edge, unless they are given supervision 

or instruction about the use of the rack by 

someone responsible for their safety.

6.  Use the rack only as described in this 

manual. 

7.  The rack is intended for home use only. Do 

not use the rack in any commercial, rental, or 

institutional setting.

8.  Keep the rack indoors, away from moisture 

and dust. Place the rack on a level surface, 

with a mat beneath it to protect the floor or 

carpet. 

9.  Make sure that there is enough clearance 

around the rack for the exercises that you will 

perform. 

10. If you will use resistance bands (not 

included) with the rack, bolt the rack to 

the floor using the holes in the bases (see 

page 5 to identify the bases).

11. Inspect and properly tighten all parts each 

time the rack is used. Replace any worn 

parts immediately. Use only manufacturer-

supplied parts.

12. Wear appropriate clothes while exercising; 

do not wear loose clothes that could become 

caught on the rack. Always wear athletic 

shoes for foot protection.

13. The pull-up bar is designed to support a 

maximum user weight of 300 lbs. (136 kg). 

Do not place more than 510 lbs. (231 kg) 

of weight on the weight rests. Do not place 

more than 150 lbs. (68 kg) of weight, includ-

ing a barbell and weights, in the landmine. 

Do not store more than 150 lbs. (68 kg) of 

weights on each weight tube. Note: The rack 

does not include a barbell or weights. 

14. Keep hands and feet away from moving 

parts.

15. Over exercising may result in serious injury 

or death. If you feel faint, if you become short 

of breath, or if you experience pain while 

exercising, stop immediately and cool down.

   WARNING: 

To reduce the risk of serious injury, read all important precautions and 

instructions in this manual and all warnings on the rack before using the rack. iFIT assumes no 

responsibility for personal injury or property damage sustained by or through the use of this 

product.

IMPORTANT PRECAUTIONS

Summary of Contents for PFBE25020.0

















Reviews: