background image

1

EZ LAN Adapter 

Installation Guide

This product is a conversion adapter that 

attaches to the USB (Type A) interface on the 

display unit so you can use it as an Ethernet 

interface. This product supports GP 4000 Series 

and GP4000R Series (both are UL-certified).

 Safety Precautions

If the equipment is used in a manner not 

specified by the manufacturer, the protection 

provided by the equipment may be impaired.

NOTE:  

When disposing of this product, follow 

your country's regulations for similar types of 
industrial waste.

Package Contents

(1) EZ LAN Adapter (PFXZCGEUUE1) x 1
(2) Attachment screws (M3) x 2

(3) Installation guide (this document)

This product has been carefully packed with 

special attention to quality. However, should you 

find anything damaged or missing, please 

contact your local distributor.

DANGER

POTENTIAL FOR EXPLOSION

Suitable for use in Class I, Division 2, 

Groups A, B, C, D or non-hazardous 

locations only.

Substitution of any components may impair 

suitability for Class I, Division 2.

Do not connect or disconnect this product 

unless power has been switched off or the 

area is known to be non-hazardous.

Failure to follow these instructions will result 

in death or serious injury.

DANGER

HAZARD OF ELECTRIC SHOCK OR 

EXPLOSION

Do not disassemble or remodel this product 

in any way. Doing so may cause an electric 

shock or fire.

Do not use this product in areas where 

flammable gases are present. Doing so may 

cause an explosion.

Do not allow water to enter the connector. Do 

not touch the connector with wet hands. 

Doing so may cause an electric shock.

Failure to follow these instructions will result 

in death or serious injury.

WARNING

UNINTENDED EQUIPMENT OPERATION OR 

LOSS OF CONTROL

Do not use or store this product at 

temperatures outside the range specified in 

this guide.

Do not use or store this product in direct 

sunlight or excessively dusty or dirty 

environments.

Do not use or store this product in an 

environment where it may be exposed to 

chemical vapors or fumes.

Failure to follow these instructions can result 

in death, serious injury, or equipment damage.

NOTICE

LOSS OF COMMUNICATION

Do not connect or disconnect this product during 

communication. Doing so may cause a communi-

cation error.

Failure to follow these instructions can result 

in equipment damage.

The information in this document is subject to change without notice.

Copyright © 2017.6 Digital Electronics Corporation. All Rights Reserved.
QGH29096 02         Printed in  

Digital Electronics Corporation
Schneider Electric Osaka Building, 
4-4-9 Kitahama,Chuo-ku, Osaka 541-0041 JAPAN
http://www.pro-face.com/

Summary of Contents for PFXZCGEUUE1








Reviews: