PRO Charging System Industrial Series Installation And Operating Instructions Manual Download Page 2

 

2

 

 

INSTALLATION AND OPERATING INSTRUCTIONS 

FOR THE FOLLOWING BATTERY CHARGING SYSTEMS: 

 

 

  

  

Total 

Independently charge 12V 

Model # 

Description 

Output 

batteries in the following 

  

  

  

systems: 

Recreation Series 

  

  

  

IS1 

One 6 Amp Bank 

6 Amps 

12V 

IS2 

Two 6 Amp Banks 

12 Amps 

12V, 24V 

IS3 

Three 6 Amp Banks 

18 Amps 

12V, 24V or 36V 

 
 
 
 

IMPORTANT NOTICE 

Please save and read all safety, operating and installation instructions before installing 
or applying AC power to your PCS on-board battery charging system.  Please contact 
PCS with any product, installation, or service questions at technical support 
(800.742.2740). 

 

 
 

INTRODUCTION 

Pro Charging Systems (PCS) has been manufacturing waterproof, on-board battery charging systems 
since 1989.  Our charging systems are designed and built tough to withstand intense vibration, extreme 
temperature variations and submersion without damaging the unit.  Our systems use temperature 
compensation in order to fully charge a battery in hot or cold environments and are controlled by 
microprocessors in order to assure precise control over each totally independent charging bank.  All of 
our chargers have true reverse polarity protection and incorporated a float maintenance mode upon 
completion of each charge cycle. 

 
 
 

 

 

 
 
 

 
 
IMPORTANT SAFETY INSTRUCTIONS 

Use of attachments not recommended or sold by PCS may result in a risk of fire, electrical shock, or injury 
to persons. 

 

To reduce risk of damage to the electrical plug and power cord, always pull by the plug rather than by the 
power cord when disconnecting charger. 
 

TABLE OF CONTENTS 

Important Safety Instructions.............................................................. Pages 2-3 
Product Summary................................................................................Pages 4-5 
Installation Instructions........................................................................Pages 5-6 
Trouble Shooting.................................................................................Page 7 
Warranty Information...........................................................................Page 8 

Summary of Contents for Industrial Series









Reviews: