Primus D55 Service Manual Download Page 62 | Manualshive

Page: 62 / 82

Primus D55 Service Manual Download Page 62

60

70276001

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

74. FAN BELT TENSION

a. Support corner drive guard and remove screws

holding corner guard to rear of tumbler.

b. Support drive guard cover and remove screws

holding guard to rear of tumbler.

c. Loosen the two mounting bracket attaching

screws.

d. Raise or lower eye bolt until proper tension is

reached.

e. Retighten all nuts and screws.

NOTE: Belt tension from fan motor pulley to fan
shaft pulley can be measured to ensure proper
installation in one of the following ways:

• Burroughs Belt Tension Gauge initial reading 60-

70 pounds.

• Force to deflect belt .38 inch at midspan with

initial tensioning 7.0 pounds

• Burroughs Belt Tension Gauge reading after run

50-55 pounds.

«
...
60
61
62
63
64
...
»

Summary of Contents for D55



















































































Reviews:

No comments