manualshive.com logo in svg

Primus D55, Service Manual, Page: 56 / 82

Share
Download
Primus D55 Service Manual Download Page 56

54

70276001

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

69. MAIN GAS BURNER AIR INLET 

SHUTTERS
(All Gas Models)
Refer to Figure 22.

Air inlet shutter adjustments will vary from 
location to location and will depend on the vent 
system, number of units installed, make-up air and 
line gas pressure. Opening the shutter increases 
the amount of primary air supplied to the burner 
while closing the shutter decreases the air supply. 
Adjust the air shutter as follows:

a. Remove access panel.
b. Start tumbler and check the flame pattern. 

Correct air and gas mixture is indicated if the 
flame pattern is primarily blue, with small 
yellow tips, and bends to the left of the heater 
section. Too little air is indicated if the flame is 
yellow, lazy and smokey.

c. To adjust the air inlet shutter, loosen locking 

screw. 

d. Slide shutter in or out as necessary to obtain 

desired  flame intensity.

e. After shutter is adjusted, tighten locking screw 

securely.

f. If the flame pattern is straight up, insufficient 

air is flowing through the tumbler. A flame 
pattern that flares to the right and left indicates 
that no air is flowing through the tumbler.

The air inlet shutters on the burner must be 
adjusted so sufficient primary air is 
metered into the system for proper 
combustion and maximum efficiency. 
Before adjusting the inlet shutter be sure 
that all lint is removed from lint 
compartment and lint screen.

W281

CAUTION

Figure 22

T197SE3C

Air Shutter

Adjusting Screw

INSUFFICIENT AIRFLOW

PROPER AIRFLOW

T196SE3C

Air Shutter

Adjusting Screw

T195SE3C

Air Shutter

Adjusting Screw

NO AIRFLOW

Summary of Contents for D55



















































































Reviews:

No comments