manualshive.com logo in svg

Primus D55, Service Manual, Page: 58 / 82

Share
Download
Primus D55 Service Manual Download Page 58

56

70276001

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

72. CYLINDER BELT

NOTE: Belt tension from step pulley to cylinder 
shaft pulley can be measured to ensure proper 
installation in one of the following ways:

• Burroughs Belt Tension Gauge initial reading 

70-80 pounds.

• Force to deflect belt .38 inch at midspan with 

initial tensioning 6.5 pounds.

• Burroughs Belt Tension Gauge reading after run 

55-65 pounds.

a. Support drive guard cover and remove screws 

that hold guard to rear of tumbler. Refer to 
Figure 11.

b. Loosen the four jackshaft assembly attaching 

screws. Refer to Figure 26.

c. Loosen adjusting nuts on outer eyebolt and 

rotate bottom nut clockwise until proper 
tension is reached. Refer to Figure 13.

d. Retighten all nuts and screws.

e. Readjust drive belt.

Figure 25

TMB1986P

Motor

Bracket

Pivot Screw

Motor

Mounting

Bracket

Adjusting

Tube

Adjusting

Nuts

Side

Bracket

Summary of Contents for D55



















































































Reviews:

No comments