PrimeLight VoxBox Pro Operating Instructions Manual Download Page 4 | Manualshive

Page: 4 / 20

background image

4

The VoxBox Pro

®

is a two-way mirror box which is positioned in front of the camera lens. It allows film

makers to shoot down-the-lens interviews while maintaining eye contact between the interviewer and
the subject. The tablet holder accessory allows the unit to be converted into a Teleprompter.

WARNINGS

This product contains sheet glass. To avoid serious injury, handle with extreme care at all times.
Check all screws and clamps are secure to ensure glass parts do not detach from the unit.
Do not allow any part of the product to get wet.

1. Intended Use

«
...
2
3
4
5
6
...
»

Summary of Contents for VoxBox Pro





















Reviews:

No comments

Related manuals for VoxBox Pro

Brand: Manfrotto Pages: 2

Brand: Manfrotto Pages: 2

Brand: GE Pages: 2

Brand: JANE Pages: 6

Brand: Zipp Pages: 39

Brand: Dacor Pages: 4

Brand: Warmup Pages: 4

Brand: rako Pages: 7

Brand: Saft Pages: 6

Brand: Yamaha Pages: 33

Brand: Yamaha Pages: 17

Brand: Zhiyun Pages: 10

Brand: YOKOGAWA Pages: 15

Brand: Zavio Pages: 31

Brand: YachtSafe Pages: 2

Brand: Öhlins Pages: 8

prodrive SUR 3A00

Brand: Öhlins Pages: 4

Brand: Öhlins Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands