Prime R1200-1D Installation & Operation Manual Download Page 4

Page: 4 / 17

Contents

Installation Considerations

The following is a list of tools needed for installation:

This section focuses on some of the vehicle considerations for install-
ing your new ampliﬁer. Pre-planning your system layout and best wiring
routes will save installation time. When deciding on the layout of your new
system, be sure that each component will be easily accessible for making
adjustments.

If you feel unsure about installing this system yourself, have it installed by
a qualiﬁed technician.

Before installation, disconnect the battery neg-
ative (-) terminal to prevent damage to the unit,
ﬁre and/or possible injury.

Before beginning any installation, follow these
simple rules:

1. Be sure to carefully read and understand the instructions before

attempting to install the unit.

2. For safety, disconnect the negative lead from the battery prior to

beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting

your unit in place.

4. Route all of the RCA cables close together and away from any high

current wires.

5. Use high quality connectors for a reliable installation and to minimize

signal or power loss.

Fuse-holder and fuse. (See
speciﬁcations for fuse rating)

Volt/Ohm Meter

Wire strippers

Wire crimpers

Wire cutters

#2 Phillips screwdriver

Battery post wrench

Hand held drill w/assorted bits

Assorted connectors

Adequate Length—Red
PowerWire

Adequate Length—Remote
Turn-onWire

Adequate Length—Black
GroundingWire

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel

lines, brake or hydraulic lines, vacuum lines or electrical wiring when
working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the

vehicle provides the best protection.

8. Avoid running wires over or through sharp edges. Use rubber or

plastic grommets to protect any wires routed through metal, especially
the ﬁrewall.

9. ALWAYS protect the battery and electrical system from damage with

proper fusing. Install the appropriate fuse holder and fuse on the +12V
power wire within 18” (45.7 cm) of the battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from

the metal to ensure a good, clean ground connection. Grounding
connections should be as short as possible and always be connected
to metal that is welded to the main body, or chassis, of the vehicle.
Seatbelt bolts should never be used for connecting to ground.

Mounting Locations

To ensure optimal performance, mount the ampliﬁer with at least
1” (2.54cm) of air gap around the ampliﬁer’s heat sink to provide
proper cooling.

Trunk Mounting

Mounting the ampliﬁer vertically or inverted will provide adequate cool-
ing of the ampliﬁer. Mounting the ampliﬁer on the ﬂoor of the trunk will
provide the best cooling of the ampliﬁer.

Passenger Compartment Mounting

Mounting the ampliﬁer in the passenger compartment will work as long as
you provide a sufﬁcient amount of air for the ampliﬁer to cool itself. If you
are going to mount the ampliﬁer under the seat of the vehicle, you must
have at least 1” (2.54cm) of air gap around the ampliﬁer’s heatsink.

Never mount this unit in the engine compart-
ment. Mounting the unit in the engine com-
partment will void your warranty.

Battery and Charging

Ampliﬁers will put an increased load on the vehicle’s battery and charging
system. We recommend checking your alternator and battery condition
to ensure that the electrical system has enough capacity to handle the
increased load of your stereo system. Stock electrical systems which are
in good condition should be able to handle the extra load of any Prime
Series ampliﬁer without problems, although battery and alternator life can
be reduced slightly. To maximize the performance of your ampliﬁer, we
suggest the use of a heavy duty battery and an energy storage capacitor.

0UZ[HSSH[PVU

Wiring the System

If you do not feel comfortable with wiring your
new unit, please see your local Authorized
Rockford Fosgate Dealer for installation.

Before installation, disconnect the battery neg-
ative (-) terminal to prevent damage to the unit,
ﬁre and/or possible injury.

Avoid running power wires near the low level
input cables, antenna, power leads, sensitive
equipment or harnesses. The power wires car-
ry substantial current and could induce noise
into the audio system.

1. Plan the wire routing. Keep RCA cables close together but isolated

from the ampliﬁer’s power cables and any high power auto accessories,
especially electric motors. This is done to prevent coupling the noise
from radiated electrical ﬁelds into the audio signal. When feeding
the wires through the ﬁrewall or any metal barrier, protect them with
plastic or rubber grommets to prevent short circuits. Leave the wires
long at this point to adjust for a precise ﬁt at a later time.

2. Prepare the RED wire (power cable) for attachment to the ampliﬁer by

stripping 1/2” of insulation from the end of the wire. Insert the bared
wire into the B+ terminal and tighten the set screw to secure the cable
in place.

NOTE: The B+ cable MUST be fused 18” or less from the vehicle’s battery.
Install the fuseholder under the hood and ensure connections are water
tight.

3. Trim the RED wire (power cable) within 18” of the battery and splice in

a inline fuse holder (not supplied). See Speciﬁcations for the rating of
the fuse to be used. DO NOT install the fuse at this time.

4. Strip 1/2” from the battery end of the power cable and crimp an

appropriate size ring terminal to the cable. Use the ring terminal to
connect to the battery positive terminal.

5. Prepare the BLACK wire (Ground cable) for attachment to the ampliﬁer

by stripping 1/2” of insulation from the end of the wire. Insert the bare
wire into the GROUND terminal and tighten the set screw to secure the
cable in place. Prepare the chassis ground by scraping any paint from
the metal surface and thoroughly clean the area of all dirt and grease.
Strip the other end of the wire and attach a ring connector. Fasten the
cable to the chassis using a non-anodized screw and a star washer.

NOTE: Keep the length of the BLACK wire (Ground) as short as possible.
Always less than 30”.

6. Prepare the Remote turn-on wire for attachment to the ampliﬁer by

stripping 1/2” of insulation from the end of the wire. Insert the bared
wire into the REMOTE terminal and tighten the set screw to secure the
wire in place. Connect the other end of the Remote wire to a switched
12 volt positive source. The switched voltage is usually taken from the
source unit’s remote amp on lead. If the source unit does not have this
output available, the recommended solution is to wire a mechanical
switch in line with a 12 volt source to activate the ampliﬁer.

7. Securely mount the ampliﬁer to the vehicle or amp rack. Be careful not

to mount the ampliﬁer on cardboard or plastic panels. Doing so may
enable the screws to pull out from the panel due to road vibration or
sudden vehicle stops.

8. Connect from source signal by plugging the RCA cables into the input

jacks at the ampliﬁer.

NOTE: All “ACTIVE” inputs must have RCA jacks connected. Switch in
2CH. position,“ACTIVE” - Front channel inputs only. Switch in 4CH.
position,“ACTIVE” - All Front and Rear channel inputs. Switch in 5CH
position,“ACTIVE” - Sub inputs for sub output. When connecting to the
5-Channel inputs, be sure to route front, rear and sub RCA cables tightly
together.

Always ensure power is off or disconnected at
the ampliﬁer before connecting RCA cables.
Failure to do so may cause damage to the am-
pliﬁer and/or connected components.

Note: When the installation requires a High Level (Speaker) input, use the
4-pin Molex connector to tie into your vehicles speaker wiring.

9. Connect the speakers. Strip the speaker wires 1/2” and insert into the

speaker terminal and tighten the set screw to secure into place. Be
sure to maintain proper speaker polarity. DO NOT chassis ground any
of the speaker leads as unstable operation may result.

10. Perform a ﬁnal check of the completed system wiring to ensure that all

connections are accurate. Check all power and ground connections
for frayed wires and loose connections which could cause problems.
Install inline fuse near battery connection.

NOTE: Follow the diagrams for proper signal polarity.

This ampliﬁer is not recommended for im-
pedance loads below 2-Ohm stereo/4-Ohm
bridged for the front/rear channels and 2-ohm
for the sub channel. Models R750-1D and
R1200-1D are not recommended for imped-
ance loads below 1-Ohm.

Prime Ampliﬁer

Mounting Hardware

Allen Wrench

Punch Level Control

4-pin Molex Connector (if
equipped)

Installation & Operation
Manual