PrimAster 39012039933, Translation From The Original Instruction Manual

Page: 26 / 44

26 GB
•
45° - position angle stop (b) between the saw blade
(6) and rotary table (14).
•
Adjust the adjusting screw (28) until the angle between
the saw blade (6) and rotary table (14) is precisely 45°.
•
It is not necessary to fix this setting because it is
maintained by the spring pretension.
•
Subsequently check the position of the angle indi-
cator. If necessary loosen the pointer (19) using a
Philips screwdriver, set to position 45° on the angle
scale (18) and re-tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/3/12)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important . To make miter cuts (inclined saw head),
the adjustable stop rail (16a) must be fixed at the outer
position.
•
Open the set nut (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
•
The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
•
Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
•
Secure the set nut (16b) again.
•
Move the machine head (4) to the top position.
•
Fix the rotary table (14) in the 0° position.
•
Loosen the set screw (22) and use the handle (1)
to angle the machine head (4) to the left, until the
pointer (19) indicates the desired angle measure-
ment on the scale (18).
•
Re-tighten the fixing screw (22).
•
Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 2/3/4/13)
The crosscut saw can be used to make mitre cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the
right in relation to the stop rail (double mitre cut).
Important . To make miter cuts (inclined saw head),
the adjustable stop rail (16a) must be fixed at the outer
position.
•
Open the set nut (16b) for the adjustable stop rail
(16a) and push the adjustable stop rail outwards.
•
The adjustable stop rail (16a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (16a) and the saw
blade (6) amounts to a maximum of 8 mm.
•
Before making a cut, check that the stop rail (16a)
and the saw blade (6) cannot collide.
•
Secure the set nut (16b) again.
•
Move the machine head (4) to its upper position.
•
Release the rotary table (14) by loosening the set
screw (26).
•
Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
•
Re-tighten the set screw (26) in order to secure the
rotary table.
•
Undo the locking screw (22) and use the handle (1)
to tilt the machine head (4) to the left until it coin-
cides with the required angle value (in this connec-
tion see also section 8.6).
•
Re-tighten the fixing screw (22).
•
Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 2/14)
•
The cutting depth can be infinitely adjusted using the
screw (24). To do this loosen the knurled nut on the
screw (24). Move the stop for the cutting depth limi-
tre (25) to the outside. Turn the screw (24) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (24).
•
Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1)
The saw is equipped with a debris bag (17) for saw-
dust and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15/16/17)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
• Unplug the machine.
• Position the sawing unit in the setting “clipping opera-
tion” (kappbetrieb).
• Unlock the movable saw blade protector (5) by means
of pressing on the lock (3).
• Lift up the saw blade protector so far that you can see
the saw blade mounting screw (29) in the notch in the
saw blade protector.
• Press down on the saw blade lock (31) until the saw
blade snaps into place.
• Remove the saw blade mounting screw (29) (note: left
hand groove).
• Remove bolt (29) and saw blade flange (30).
• Take off the saw blade (6) with caution (risk of injury
through saw blade teeth).
• Place the new saw blade (6) onto the inner saw blade
flange (32), observing the correct size and the turning
direction of the saw blade.
• Put the outer saw blade flange (30) in place and firmly
tighten the screw (29).
• Return the saw blade guard (5) to the correct position.
8.11 Using the laser (Fig. 3/19/20)
•
To switch on: Move the ON/OFF switch of the laser
(34) to the “1” position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
•
To switch off: Move the ON/OFF switch of the laser
(34) to the “0” position.