Pridom PFCM123HX Owner'S Manual Download Page 3

Model

Lowest Voltage of 
CPU Emitting Signal

Rated Voltage

8m

3.0V(Dry batteries R03/LR03

2)

2.4V

Remote Controller Specifications

1. Operating Mode:  AUTO, COOL, DRY, HEAT(cooling & heating models only), 
    and FAN.
2. Timer Setting Function in 24 hours.

O

O

O

O

3. Indoor  Setting  Temperature Range    :  6

  2 F~86 F(17 C~30 C).

4. Full function of LCD (Liquid Crystal Display).

Environment

Signal Receiving 
Range

Performance Feature

Function buttons

1

2

 Each time the button is pressed, the operation 
 mode is selected in a sequence of  following:
   
  

3

MODE  Button    

 

3

3

4

4

3

4

ON/OFF Button    

 

Operation starts when this button is pressed 
and stops when this button is pressed again.

NOTE: 

Please do not select HEAT mode if the 

machine you purchased is cooling only type. Heat 
mode is not supported by the cooling only 
appliance.

AUTO

COOL

DRY

HEAT

FAN 

SLEEP Button    

 

NOTE: 

While the unit is running under SLEEP

mode, it would be cancelled if MODE, FAN 
SPEED or ON/OFF button is pressed.

Active/Disable sleep function. It can maintain 
the most comfortable temperature and save 
energy. This function is available on COOL, 
HEAT or AUTO mode only .

 SWING V Button    

 

Used to stop or start horizontal louver move-
ment and set the desired up/down air flow
direction. Push once, the louver changes 6 
degree in angle. Keep pushing more than 2 
seconds, the louver will swing  up and down
automatically.

MODE

FAN SPEED

M

AUTO

COOL

DRY

HEAT

FAN

Sliding door
   (closed)

MODE

FAN SPEED

SWING V

SLEEP

TIMER ON

TIMER OFF

CLOCK

RESET  LOCK

M

AUTO

COOL

DRY

HEAT

FAN

4
5

7

8

9

10

11

12

13
14

15

2

1

TURBO

LED

Sliding door
   (opened)

RG05F2/BGEU1

O

O

O

O

23 F~140 F(-5 C~60 C)

SWING H

16

5

 SWING H Button

Used to stop or start vertical louver movement 
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press.If keep pushing more than 2
seconds,the vertical louver swing feature is 
activated.(Not applicable to all the units,please
refer to the OWNER S MANUAL for details).

SELF CLEAN

6

I FEEL

I FEEL /SELF CLEAN Function

Press this button less than 2 seconds will 
initiate  I FEEL function. And if keep pressing 
this button more than 2 seconds, the 
SELF CLEAN function is initiated.  

6

Summary of Contents for PFCM123HX









Reviews: