background image

7.2 NORMAL OPERATION WITH MULTIPLE REMOTE CONTROLLER INSTALLED

Press the ON/OFF button. Then the Power light is lit on the remote controller and the setting 

temperature is displayed on each remote controller.

Set the temperature as you require (the tempreature setting can be change only by the priority unit). 

If you desire to transfer the priority setting, you can transfer it by pressing ON/OFF button.

)

 

Open a hot water tap, and ensure the Burning light is ON. Mix cold water with the hot if you 

need.

Close the hot water tap, and the Burning light is OFF.

19

WARNING

Water temperatures above 50 

ºC

 can cause severe burns or death from scalding. Children, 

the disabled and the elderly are at a high risk of being injured. Feel the water temperature 

before bathing or showering. Do not leave children, disabled persons, or the elderly 

unsupervised. The Australian Standards AS 3498 gives full details of the requirements for 

supply of controlled temperature to ablution outlets (bathrooms) and is required to be 

conformed to under all plumbing codes within Australia.

!

NOTE

When the remote controller used on EN20CF-LP70 & EN20CF-NG70 model, it is able to 

adjust the setting temperature in the range of 38

ºC

 to 65

ºC.

 

 

 

ON/OFF

button

Reduce 

temperature 

button

Increase 

temperature 

button

Summary of Contents for EN Series



























Reviews: