background image

• Turn OFF the pressure washer and depress the trigger to 

release the pressure trapped inside the unit.

• Remove the garden hose and the pressure hose.

• Turn ON the pressure washer and leave it running 5 

seconds to eliminate almost all the water trapped inside the 

pump.

• Disconnect the pressure washer and put away the cable.

• Store the pressure washer and the accessories in a dry 

environment with controlled temperature. Do not store the 

pressure washer and the accessories where temperature 

can drop to 40 °F.

                          DAMAGE DUE TO FREEZING IS NOT 

COVERED BY THE WARRANTY.

• The pressure washer design includes a permanent 

lubrication system. It is not necessary to check and replace 

oil.

                          If there is an oil leak, go to a

                                Authorized Service Center.

                            Disconnect the power cable from the 

power supply before carrying adjustments, service or 

maintenance to the pressure washer.

9

• Carbon brushes shall be checked periodically and be 

replaced always in a                                 Authorized 

Service Center when worn.

• After being replaced, ask the technician to inspect if the 

carbon brushes move freely in the carbon brushes housing.  

Ask to turn ON the pressure washer 5 minutes to even out 

the carbon brushes and commuter contact.

• Only use original                                 spare carbons 

specifically designed with the hardness and electric 

resistance for each type of motor. Carbon brushes that are 

lout of specification may damage the motor.

• When replacing carbon brushes always replace both.

Carbon brushes replacement

Maintenance

Winter storage

Water filter

Cleaning and care

Lubrication of connections

Lubrication of nozzles

Lubrication of the pressure washer

• Any foreign particle entering the pressure washer pump 

can damage it. To prevent this possibility, the pressure 

washer is built with a water filter.

• The water filter inner scream shall be kept always clean to 

maintain a continuous water flow into the pressure washer 

preventing damages to the pump.

• To clean the screen, remove the water filter from the fast 

connector in the garden hose. Unthread to remove the 

screen. Handle with care to not damage it.

• Immediately, set back the screen and the fast connector 

of the garden hose to prevent foreign particles entering the 

pump.

• Keep the pressure washer free of dust.  Never use water 

or chemical cleaners to clean the pressure washer.  Clean 

only with a clean and dry cloth.

• Always keep the air vents clean and free of obstructions to 

guarantee the adequate cooling of the motor.

• Regularly inspect all the mounting screws and make sure 

the screws are tight. If one screw is losing, tighten 

immediately.

• The shield and the motor are the pressure water heart. 

Use care no grease or water affect them.

• Regularly check the power cable to detect any type of 

damage. If damaged, replace the cable in a

                                Authorized Service Center.

The pressure washer hose, high-pressure gun and lances 

connections shall be cleaned regularly to prevent leaks and 

damage to each connection seals.

• Nozzles shall be regularly lubricated with non-soluble oil 

or light oil.

• A blocked nozzle makes the pressure pump pressure rise 

too much. It shall be cleaned immediately.

1)

 Remove blockage in the nozzle introducing the nozzle 

cleaner through the center orifice.

2)

 Purge the nozzle with water. Restart the pressure washer 

and press the spray gun trigger.

If pressure is still high, repeat steps 

1

 and 

2

.

CAUTION

CAUTION

WARNING

ENGLISH

DRAFT 

DRAFT 

DRAFT

Summary of Contents for 26024

























Reviews: