4
Note: The Footlight
base will illuminate whenever the cord is plugged into an outlet to indicate the heater is electrically
activated.
Caution: Plug directly into a wall outlet. This heater is not intended for use with an extension cord.
3. Turn the “Thermostatic Control” knob to its “HI” position. There may be a vibrating sound when the heater is turned on. This is
normal and should last only about a half minute. When using the heater for the first time, there may also be a slight odor or light
smoking as manufacturing coatings “burn” off. This, too, is normal during the first several uses.
4. Allow the heater to operate on its “HI” setting for at least three minutes to bring the heating element to its optimum operating
temperature. Anytime after that, the “Thermostatic Control” knob may be adjusted to any position necessary to maintain the desired
comfort level.
Remember, after the “Thermostatic Control” knob is turned to any ON position below “HI”, the heater will be continually turning
itself ON and OFF to control the heat output. This may not always be obvious because, due to residual heat in the heating element,
it will continue to glow at most settings. You may also hear a slight “clicking” sound as the automatic switch cycles the heating
elements ON and OFF, or, when in a darkened room, see a flash of light.
If additional heat is desired, turn the “Thermostatic Control” knob to a higher setting. This will lengthen the ON cycle and the heater
will produce more heat. If less heat is desired, turn the knob to a lower setting. The ON cycle will then be shortened, producing less
heat.
5. After use, turn the “Thermostatic Control” knob to the OFF position and disconnect the plug from the wall outlet.
Care, Cleaning and Storage...
Allow heater to cool completely before any care or cleaning or storage. Also be sure heater is turned off and unplugged.
1. Do not pour or spray any water, cleaners, or any liquid on or into any portion of the heater. Do not submerge heater in any liquid.
2. Use a soft lint free damp cloth and a mild detergent to clean the exterior surfaces. Harsh or abrasive cleaners will damage the finish.
3. Occasionally the parabolic reflector inside the grille will need to be cleaned to remove dust accumulation. To remove dust from the
parabolic reflector, you may purchase a specially designed cleaning device such as the one offered on the Important Instructions
sheet enclosed. You may also dust the reflector by following these simple steps: 1) Unplug the heater and allow to cool; 2) support
the heater on its back; 3) slip a soft lint free cloth through the grille; 4) move the cloth over the surface of the parabolic reflector by
inserting a long thin handle (such as a dowel or the handle portion of a wooden spoon) through the grille, using it to slide the cloth
from spot to spot over the surface of the reflector; 5) remove the handle and the cloth when the surface is dust free.
Note: If you allow dust to build up on the parabolic reflector, the dust accumulation may cause the heater to overheat and the
warning buzzer to sound.
If this should occur, clean the parabolic reflector as previously instructed. Once the dust is removed, the
heater should work normally again. If, however, after cleaning, the heater does not work properly or the buzzer continues to sound,
send the heater to the Factory Service Department listed on the next page.
4. Wrap the cord around the base pedestal and store heater in a dry location.
5. The Footlight
base contains a standard 4 watt night light bulb (type C7) which can be found at any hardware or discount store. Should
there ever be a need to replace the bulb*, it’s easy to do. First, unplug the heater. Lay the heater on its back with the base towards
you. Next, tilt the base upwards slowly until you see the metal plate on the bottom of the base. The bulb is in the opening between
the metal plate and the front of the base. Slip your thumb and forefinger into the opening and unscrew (turning counterclockwise)
and discard the original bulb. Then screw in the replacement bulb.
*CAUTION: Use ONLY a standard 4 watt, 120 volt nightlight bulb (type C7) for replacement of the bulb in the Footlight
base; use of a higher watt bulb could cause a fire.
