Fig. B
3
ON. In addition, the buzzer may sound and the heater will shut off if too much dust or dirt has accumulated
on the parabolic reflector. To clean the parabolic reflector, see cleaning instructions on page 4.
With the “Thermostatic Control” knob (Fig. B) set to the “HI” position, the electricity is supplied to the
heating elements 100% of the time and the heater is ON constantly. In the “LOW” position, electricity is
supplied to the heating elements only part of the time. This varies with the room temperature. The colder
the temperature is in the room, the more often the heater will cycle on. The heater will automatically cycle
on and off at the “LOW” setting and maintain a constant temperature.
The desired comfort level can be maintained by adjusting the “Thermostatic Control” knob and thereby
regulating the total heat output of the unit.
The Footlight
base feature…
The Footlight
base lights up whenever the cord is plugged into an outlet. It not only produces an attractive glow, but also lets you know
at a glance when the heater is plugged in. And, the glow is energy efficient. The Footlight
base uses no more power than a standard
night light.
The Footlight
base operates independently from the rest of the heater. It is even independent of the automatic safety switch (which turns
the heater’s element off if the heater is tipped in any direction) and the buzzer (which sounds an audible warning if the heater is tipped
while the element is cycled on). The Footlight
base is designed to let you know at all times that the heater is plugged in. That means
that if the heater is plugged in:
1. The Footlight
base will glow even if the thermostatic control is turned to OFF.
2. The Footlight
base will continue to glow even if the unit is tipped and is buzzing.
3. The Footlight
base will glow, but the buzzer will not sound, if the heater is plugged in and tipped, and the element is not cycled on.
Your Presto
Parabolic Heater is shipped completely assembled. Before using the heater for the first time, familiarize yourself with the
parts of the heater (Fig. A) and read the information on the following pages. For proper operating position, stand the heater upright with
the bottom of the base resting flat on the floor.
Positioning the heater...
When positioned correctly, the parabolic heater will keep you toasty warm. Follow these suggestions for maximum warmth:
1. Point the front grille towards the area in which heat is desired.
2. Check to make sure there are no objects between you and the heater. Such objects will absorb the heat and prevent it from reaching
you.
3. Place the heater at least 3 feet, but no more than 10 feet away. The parabolic design of the reflector focuses heat at persons 3 to 10
feet away. Thus for your entire body to enjoy the heat produced by the heater, it must be placed at least 3 feet from you. Placing it
closer will turn the heater into a foot warmer, rather than a body warmer. Experiment with various positions until you find the one
that is right for you.
4. Remember, this unit is primarily a people heater rather than a room heater, and using it to heat a room is not recommended. The
infrared heat produced by this heater will travel through glass, just like the sun’s rays. If the heater is aimed at a window, objects
outside will be heated.
When using any heater, the following safety precautions should always be observed:
Close attention is necessary when the heater is used where children are present.
The heater should always be in a stable, upright position with at least 3 feet of space between the front of the unit and any other
surface.
The heater should never be placed in a closed area such as beneath furniture, in cabinets, or beneath or behind curtains or drapes.
Nor should it be hung from a wall or ceiling.
Heat produced by any heater tends to pull moisture from the air. It is recommended that you avoid sitting with your face directly in
front of the heating element. The intense heat may dry your eyes and cause irritation.
Operating the heater...
1. Turn the “Thermostatic Control” (Fig. B) to the OFF position.
2. Plug the power cord into a 120 volt, 60 cycle circuit which serves nothing else and has a polarized outlet. As a safety feature, this
appliance has a polarized plug (one blade is wider than the other). This plug will only fit in a polarized outlet one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature. Because the heater is a 1000 watt appliance, it is normal for the plug to feel warm to the touch during operation.
