background image

13

2018 Voxx Electronics Corporation. All rights reserved.

  Replacing Remote Control Batteries

 5 Button Remote Control - Model 185SP

 

The CR2032 battery inside each remote control should last approximately 1 year under 

normal use. When the batteries become weak you will notice the remote control range 

(the distance from the vehicle the remote control will work) deteriorate and the small LED 

on the remote control will dim. To replace the remote control batteries:
   

1. Using a coin, disassemble the halves of the remote

   

    control.

   

2. Remove the old battery, observing the +/- symbols on the

   

    batteries and replace with a new battery.

   

3. Reassemble the halves of the remote control

   

4. Test operation of the remote control.

 5 Button Remote Control - Model 185TWSP / 18TWLOR

The CR2450 battery inside each remote control should last approximately 1 year under 

normal use. When the batteries become weak you will notice the remote control range 

(the distance from the vehicle the remote control will work) deteriorate and the small LED 

on the remote control will dim. To replace the remote control batteries:
   

1. Using a coin, disassemble the halves of the remote

   

    control.

   

2. Remove the old battery, observing the +/- symbols on the

   

    batteries and replace with a new battery.

   

3. Reassemble the halves of the remote control

   

4. Test operation of the remote control.

Summary of Contents for APSSECRS RF
















Reviews: