Prestige APS25Z Installation And Reference Manual Download

Page: 12 / 15

APS25Z_RevA_08/18

Quick Reference:

Wiring Diagrams

Door Lock Connections

Single-Wire Negative Multiplex Door Locks (Relays required)

Verification:

The vehicle wire registers variable Ground values when the Lock and Unlock switches are activated. Please

consult the vehicle-specific wire and location chart for resistor values.

Single-Wire Positive Multiplex Door Locks (Relays required)

Verification:

The vehicle wire registers variable 12V+ values when the Lock and Unlock switches are activated. Please

consult the vehicle-specific wire and location chart for resistor values.

Lock

Unlock

Vehicle Door Lock
Control Relays

RED ( - ) Lock Output

Green ( - ) Unlock Output

87a

Fused +12 Volt

Battery Source

Ground

Resistor

Lock

Unlock

Vehicle Door Lock
Control Relays

RED ( - ) Lock Output

Green ( - ) Unlock Output

87a

Fused +12 Volt

Battery Source

Resistor

Summary of Contents for APS25Z
















Search results

Summary of Contents for APS25Z

Reviews:

Related manuals for APS25Z

Brands by name

Popular brands

Prestige APS25Z, Installation And Reference Manual

Search results

Summary of Contents for APS25Z

Reviews:

Related manuals for APS25Z

Brands by name

Popular brands