Prestige 120 Installation, Operating And Maintenance Instructions Download

Page: 35 / 48

EN • 35

ENGLISH

FRANCAIS

NEDERLANDS

ño

ALIAN

TSCH

664Y3300

mCBA pARAmETERS FoR THE SpECIALIST

settIng the parameters

parameter mode

To access Parameter mode when the installation is in Standby mode, press “

mODE

” once.

You can scroll through the list of parameters by pressing “

STEP

” each time. To modify the value of the parameter, use the“

” or “

”

keys.

Next, press “

STORE

” to record the modified value. The screen will flash once to confirm that the value has been stored.

To activate the modified parameters, press “

mODE

” again (this will switch you to Info mode). However, if you do not press any key, the

system returns to Standby mode after 20 minutes and activates the changes.

Factory setting

Key

Display

Description of the parameters

Prestige

120

STEP

Setting the hot water temperature

STEP

Hot water

generation

00 =  Off
01 =  On
02 =   Off + pump active

constantly

03 = On + pump active

constantly

STEP

Switching

heating On/

Off

00 =  Off
01 =  On
02 =   Off + pump active

constantly

03 = On + pump active

constantly

STEP

Maximum temperature in central heating mode

Key

Display

MODE

Summary of Contents for 120

















































Search results

Summary of Contents for 120

Reviews:

Related manuals for 120

Brands by name

Popular brands

Prestige 120, Installation, Operating And Maintenance Instructions

Search results

Summary of Contents for 120

Reviews:

Related manuals for 120

Brands by name

Popular brands