Presenza QR001 Installation Manual And User'S Manual Download Page 18

 18
 

Care and Cleaning

RANGE HOOD

WARNING: 

Failure to maintain basic standards of care 

and cleaning of the range hood will increase the risk of fire.

The range hood should be cleaned (regularly internally and externally) to preserve its appearance and performance. 

Do:

Do Not:

 

- Always clean in the direction of the grain (original  

polish lines) .

 

- Clean the range hood periodically with hot, soapy 

water and a clean cotton cloth . 

 

- Always rinse well with clean water two or three 

times after cleaning . Wipe completely dry with a 
soft non-abrasive cloth.

 

- After cleaning, you may polish with a non-abrasive 

stainless steel polish or cleaner. Always rub lightly 
and with the grain .

 

- Ensure that the venting system is free of debris, if 

you have one .

 

- Do not use corrosive or abrasive detergents, steel 

wool, or scouring pads . These will scratch and 
damage the stainless steel surface .

 

- Do not use corrosive or abrasive detergents, or any 

products containing chloride, fluoride, iodide, or 
bromide on this product, as they will deteriorate 
the surface rapidly .

 

- Do not allow cleaning compounds, salt solutions, 

disinfectants, or bleaches to remain in contact with 
the product for extended periods of time.

 

- Do not allow deposits to remain for long periods 

of time on the range hood . Rinse with water 
immediately and wipe dry with a clean cloth .

 

- Do not let plaster dust or any other construction 

residue enter the hood . During construction or 
renovation, cover the hood .

 - Combustible products used for cleaning such as 

acetone, alcohol, ether, or benzol are highly explosive 
and should never be used close to a range or stove .

FILTERS / BAFFLE NETS

The filter fitted by the factory is intended to filter out residue and grease from cooking. You do not need to replace them on a regular basis, 
but you should keep them clean .

Do:

Do Not:

 

- Clean the filters / baffle nets once a month using 

non-abrasive detergents, either by hand or in 
the dishwasher . When using a dishwasher, set 
the dishwasher to a low temperature and a short 
cycle setting. The filter may become discoloured 
in a dishwasher, but this does not affect its 
performance .

 

- Dry the filters / baffle nets before re-installing them 

in the range hood .

 

- Do not allow oil to accumulate over more than 80% 

of the filter surface. Oil accumulations may drip oil 
onto the range .

Summary of Contents for QR001
























Reviews: