background image

Page 6

Filter Replacement Procedure

Step 1:  

Shut off the water to the filter housing by turning the bypass valve to “BYPASS” or “OFF”

Step 2:  

 The bowl of the system can be removed by turning it clockwise (see Figure 1).  Use the supplied filter 

wrench to loosen the housing.

Step 3:  

Remove the old filter and discard.

Step 4:  

 Clean the filter housing with a mild soap solution and rinse with water.  Check O-ring and lubricate with 

water soluble lubricant.   

  

NOTICE

  Petroleum based lubricants (such as Vaseline®) must not be used

Step 4:  

Replace filter.

Step 5:  

 Reinstall by turning the filter bowl counter-clockwise (see Figure 1) onto the lid.  Make sure O-ring is 

properly seated.

  

NOTICE

   Hand tighten housing.  Wrench should only be used to loosen housing. 

Step 6:  

Turn bypass valve back to “FILTER”

Step 7:  

Check for leaks.  Monitor unit for leaks for 24 hours after filter replacement.

Troubleshooting

Problem

Cause

Solution

Filter bowl has no water in it. Water is not turned on at Main

Check that the water is on at Main

Valve turned to “BY-PASS” or 

“OFF”

Make sure valve is turned to the “FILTER” posi-

tion.

Leaking at the bowl.

O-Ring kinked or not seated. 

Check / Replace / Re-seat O-Ring.

Bowl not tightened enough.

Tighten bowl.

Leaking at the valve fit-

tings. 

Improper installation / Not enough 

plumber’s tape on fitting

Replace or repair fittings.

Leaking at top of valve (lid).

Faulty lid.

Call Watts at 1-800-752-5582 for a replacement

Low water flow / pressure

Filter clogged

Replace Filter

 

Summary of Contents for WH-LD









Reviews: