P-9
P-10
P-11
P-12
P-13
P-14
P-15
P-8
In case the signal intensity is too weak, the image will remain inferior
whatever you adjust the antenna, and cause loud noise wave, shaking image and
inferior sound, etc., which is not TV fault. If the image remains inferior when using
telescopic antenna, please try to use the external antenna or CATV.
Notice:
11. Technical Parameters
Phenomena below does not necessarily mean failure with TV set. Please check
following before you request for repair. No repairable components exist in the
machine. Don't try to dismantle and improve the monitor, and the high voltage in the
machine may cause danger. Maintenance and adjustment of the monitor is subject
to professionals.
No picture, no sound:
No image:
Whether the correct Channel selected;
Automatically set up the Receiving Channel again;
Any new place is subject to re-setup of channels.
No sound:
Whether the volume is turned to the end or the Sound System is incorrect;
Whether earphone plugged in;
Whether ERASE functions under too weak signal.
Dark picture:
Whether brightness and contrast adjusted correctly;
Whether environment temperature is too low.
Unclear or unstable image:
Whether antenna adjusted correctly;
Maybe too weak signal received at the receiving place.
Achromatic or flashing color:
Whether color adjusted well, whether the decoloration actions under the Color
system with too weak proper signal.
Improper connection with AC adapter or Care adapter;
Use of unauthorized power supply;
TV set is on standby status.
Upside down or lateral inverted picture:
Improperly adjusted Horizontal or Vertical in the remote control.
10. Troubleshooting methods
2.6.2 Video Setting Page
TV systems: when connecting video output, the output system of the product and the
system of TV should corresponding match, otherwise no color shows.
Abnormal, "NTSC" and "PAL" are available to choose; the default value
is "NTSC".
Home Page: return functions setting page
Product Name: LCD Color TV Receiver
Display Device: Color TFT-LCD
Receiving frequency range: Full frequency search: 48.25MHz-863.25MHz
Fixed channel search: AIR: 55.25MHz-801.25MHz
CATV: 55.25MHz-799.25MHz
Screen Size: 7 inches
Resolution: 480(H)
RGB
234(V)
Audio Output: 0.5W
2
Loudspeaker: 2
27mm
Connecting Terminal: External antenna input jack, Audio / Video (AV) input/output
jack, earphone jack, External power supply jack.
Applicable Power Supply: Three options:
1. AC Power supply AC adapter
2. Car adapter 12V 12-24V
3. Build-in battery 7.4V/1700mAh(optional)
Power Consumption: No built-in battery: 8W
With built-in battery: 10W
Outer Dimension: 205mm
117mm 36mm
Weight: about 600g
after some items in this manual means it is available with this function.
WARNING:
This operation instruction is only intended for reference. No further notice is
available to any modification of all information contained therein. Due to
continuing improvements, the features and design are subject to change without
notice.
No repairable components exist in the machine. Don't try to dismantle and
improve the monitor, and the high voltage in the machine may cause danger.
Maintenance and adjustment of the monitor is subject to professionals.
WARNING:
To prevent injury, this apparatus must be securely attached to the floor/wall in
accordance with the installation instructions.
The mains plug is used as the disconnect device, the disconnect device shall
remain readily operable, and it shall be disconnected from the mains completely.
The plug is used as disconnect device form the mains supply, the plug shall
remain readily operable.
The apparatus should not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
No naked flame sources, such as lighted candles, should be placed on the
apparatus.
Batteries (battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced. Replaced only with the
same or equivalent type.
4.2.Press or to select the item SOUND-SYS:
Then press , the SOUND-SYS displays in the order of BG5.5M, I6.0M, DK6.5M,
L6.5M and M4.5M.
4.
SYSTEM
COLOR-SYS, SOUND-SYS, BLUE BACK, HORIZONTAL, VERTICAL and ZOOM
displays on the screen as below description:
4.1.Press or to select the item COLOR-SYS:
Then press to revolve the screen in the order of AUTO, PAL, SECAM, NTSC,
PAL N and PAL M. Please choose carefully this system correctly. Otherwise, it may
cause achromatic or inferior color. It is recommended to select on AUTO position.
Notes:
1)Please set the SOUND-SYS at local one.
2)In case with picture while without sound or with noise, please check the
SOUND-SYS for correct setup first.
4.3.Press or to select the item BLUE BACK:
Press or can realize the ON/OFF of BLUE BACK under no signal.
4.4.Press or to select the item HORIZONTAL:
Press or can realize HORIZONTAL, press again to resume the picture.
4.5.Press or to select the item VERTICAL:
Press or can realize VERTICAL flip, press again to resume the picture.
4.6.Press or to select the item ZOOM:
Press or can realize the selection of picture modes:4:3 mode, and 16:9 mode.
5. PRESET (When TV function moves to full frequency search, operate as the
below instruction.)
POSITION, REMEMBER, BAND, SWAP, FINE, SEARCH and AUTO-SEARCH will
display on the screen as below description:
5.1.Press or to select POSITION, and press or to set.
5.2.Press or to select REMEMBER, and press or to select ON, this
channel will be displayed when selected. When REMEMBER is OFF, this channel
will not be displayed.
5.3.Press or to select BAND ,and then press or to switch of V-L,V-H
and U.
5.4.Press or to select SWAP, then press or to select the channel No.
Press MENU to confirm SWAP.
5.5.Press or to select FINE. Then press or to adjust channel frenquency
by little.
5.6.Press or to select SEARCH. Then press or to start searching
forthward or backward. TV searching indicater bar will turn to green from red after
search TV signal. TV storage system will identify as no signal if TV channel are on
too weak signal.
5.7.Press or to select AUTO-SEARCH. Press or to start auto searching
from channel 0 in turns of V-L , V-H and UHF. Station of sufficient strength will be
memorized and searching stops.
6. PRESET (When TV function moves to fixed channel search, operate as the
below instruction.)
POSITION, REMEMBER, ANTENNA and AUTO-SEARCH will display on the screen
as below description:
6.1.Press or to select POSITION, and press or to set.
6.2.Press or to select REMEMBER, and press or to select ON, this
channel will be displayed when selected. When REMEMBER is OFF, this channel
will not be displayed.
6.3.Press or to select "ANTENNA" item, Press or to select AIR,
CATV-STD, CATV-HRC, CATV-IRC.
6.4.Press or to select "AUTO-SEARCH" item: press or to auto search.
In
order
to
watch
TV
properly
1.
Set the desired OSD language by pressing LANG.
2. Ensure the COLOR-SYS, SOUND-SYS is correct by checking from SYSTEM
menu.
3. Select AUTO-SEARCH in PRESET menu, and start auto search TV signal.
4. Adjust the length, angle and direction of the telescopic antenna to obtain optimum
image.
1. Usage
of
memory
facility
(USB&CARD)
This product supports almost all types of USB, Multi Media Card (MMC), SD,
Memory Stick (MS) in the market.
1)This product supports various USB & CARD within 4G (beyond the capacity, some
abnormal phenomenon may occur. )
2)This product supports JPEG, MP3, WMA, VCD, AVI ect. (some substandard files,
like DIVX3 and compress formats, are not available and Black screen may occur.)
Notice:
Able to play very smoothly when data stream is below 2000KBP/S, it might
pause when the data stream is above 2000KBP/S.
The product may be not available to play or may need to restart once browsing
pictures too big. It is suggested within 12M.
9. CARD mode operation
2.5
Common
functions'
operation
instruction
: Play/pause : Fast forward : Forward file
: Stop : Fast backward : Backward file
ZOOM: When playing, press "ZOOM" to zoom out the picture to browse.
REP: When playing, press repeat key to realize the following functions:
"single repeat", "all repeat," "cancel".
SOUND: Track switch (excluded unsupported file).
EXIT: When playing, press " " to stop, then repress " " to return main interface,
or press the " " to return main interface directly.
2.6
Setting
Press direction key to select 'SETUP' item, press / to select upward/downward
file, then press 'OK' to confirm.
2.6.1 Common Setting
Languages: Chinese, English and other multi-languages are available.
Sound: Select your favor language to play when various sound languages are
supported for some videos.
Subtitle: Select your favor language to play when multiple subtitles languages are
supported for some videos.
Default Value: factory reset
Home Page: return functions setting page
1 .Set the desired OSD language by pressing LANG.
2 .Ensure the COLOR-SYS, SOUND-SYS is correct by cheching
from SYSTEM menu.
3 .Select AUTO-SEARCH in PREST menu, and start auto search
TV signal.
4 .Adjust the length, angle and direction of the telescopic antenna
toobtain optimum image.
Notice
ln case the signal intensity is too weak, the imag will remain inferior
whatever you adjust the antenna, and cause loud noise wave,
shaking image and inferior sound, etc.,which is not TV fault. Lf the
image remains inferior when using telescopic antenna, please try to
use the external antenna or catv.
8.
ln order to receive clearer picture
The USB plug of this device do not support Multi-media devices such as Card
reader, portable hard drive, MP3, Mp4.
When facing problems from the device, please unplug the device for 5 seconds
then re-start (reset).
2.
Playing
multi-media
files
Press 'MODE', switch to CARD mode, in the interface five functions ('PHOTO',
'MUSIC', 'VIDEO', 'SLIDE SHOW' and 'SETUP') are available. Insert USB or CARD
(Once occur at the same time, press MENU to switch between USB or CARD in the
interface).
2.1.
Browse
Picture
Press direction key to select 'PHOTO', then click 'OK' to open file; press
upward/downward key to select picture, click 'OK' to read. When browsing pictures,
press 'S.SHOW' once to switch a mode of pictures displaying.
When reading picture files, press direction key for fast operation of the
following functions:
Left direction key: anticlockwise 90
Right direction key: clockwise 90
Up direction key: up/down/left/right mirror
Down direction key: up/down/left/right mirror
After the operation of rotation or mirroring, press " " key to continue playing.
Notice:
Background music can not be open while reading picture, other function
will not work when using zoom function.
2.2
Play
music
Press direction key to select 'MUSIC' item, press 'OK' to open file from storage;
press direction key to select the file, and then press 'OK' to play music.
2.3
Play
movie
Press direction key to select 'VIDEO' item, press 'OK' to open the file from storage,
press direction key to select file, then press 'OK' to play movie.
2.4
Slide
show
Press direction key to select 'SLIDE SHOW' item, press 'OK' to open file from
storage; press direction key to select file, press 'OK' to play. While playing,
press 'OK' to turn ON/OFF background music.
Note:
The display languages of file or movie named are to be simplified Chinese
and international standard character. If languages displayed are not the above
character or character over 8 digits, disorder characters may occur.
