background image

Preferred Instruments 

Div. of Preferred Utilities Manufacturing Corp

.  

Phone (203) 743-6741, Fax (203) 798-7313 

                                                                                                  www.preferredinstruments.com

 

Installation and Operation Manual JC-22-PL2-1006      rev. 6    6-5-17  

 Page 6 of 12 

B. SPECIFICATIONS 

 
Mechanical

:    

 

 

17.50L” by 7.50” W by 5.90” H 

Weight:  

 

 

 

21lbs 

Operating Temperature:

      

0

°

F to +140

°

F (-18

°

C to +60

°

C) 

Electrical

 

 

 

Voltage: 120 VAC +10% - 15%, 50/60Hz 

 

 

 

 

Power consumption: 28VA 

Travel: 

 

 

 

6” linear, 60 sec. stroke 

Thrust:

   

 

 

 

150 lbs 

Damper Switch, Fully Open:  

10A, 250VAC 

Set Point: 

 

 

 

Adjustable from 0-100% corresponds to: 

 

 

 

 

 

  0 to +2.0 w.c. or  0 to -2.0 w.c.  (see pg 12 to change) 

Dampening:

   

 

 

Adjustable from 0-100%, corresponds to 1.5 to 15 seconds  

 

 

 

 

 

For 90% response to a step change 

Dead Band:

   

 

 

Adjustable from 0 to 100%, corresponds to .01 to .08” w.c. 

Proportional Band:

    

 

Adjustable from 0 to 100%, corresponds to .03 to .2” w.c. 

 

 

 

 

 

If the actuator deviated by amount that is greater then PB,  

 

 

 

 

 

the actuator will run at full speed 

 

Indicators:

 

 

 

 

SET-POINT. Whenever the actuator is positioned within  

 

 

 

 

 

the dead band of the set point  

 
 

 

 

 

 

DECREASE. Whenever the arm is commanded to retract 

 

 

 

 

 

 

 

 

 

 

 

INCREASE. Whenever the arm is commanded to extend 

 
                                               

17.50                                            6.71 

                                               16.50 
 
2.69 
 
 
5.38 
 
 
 
 
 
                                                                                                                                     

7.69 

 

                                                                                                     6.00 

    4.38                                                                                                                                                                    5.95   

                                             2.50                                                                                                                      1.82   

                    1.7                 8.56                                                                        .82                       1.93 

                                                                                                                                         3.75  

                                                                                                                

7.50 

 

Summary of Contents for JC-22-PL2-1006













Reviews: