background image

Page 11

For technical questions, please call 1-888-866-5797.

ITEM 63022 

        

SAFETY

SETU

p

Op

ERA

TION

M

AINTENANCE

WARNING!  The Bit should NOT turn at idle.  

 

If it is turning at idle, immediately discontinue 

using the Auger and contact a qualified 

service technician to adjust the Auger.
6.  Once the Engine is started,  

press the Choke down slowly to open it.

Note:

 Moving the Choke Lever too 

fast could stall the engine.
7.  If the Engine 

does not

 start,  

press the Primer 

one

 more time.   

Raise the Choke if it is pressed down, 

and again attempt to start the Engine. See Figure D.

Throttle

Figure D

8.  Stand with a solid stance on stable 

ground. Brace yourself and maintain a 

proper grip with both hands on the Frame 

whenever the Engine is running.

9.  Accelerate the Engine to full throttle just before 

starting to drill by squeezing the Throttle.  

Keep the Engine at full throttle the entire time 

you are drilling, unless a problem arises.

10. 

Do not drill at an angle

.   

Keep the Bit vertical at all times.

11.  Allow the Bit to drill for you.  Exert only light 

downward pressure.  If you attempt to force 

the Auger, damage to the Auger and Bit can result.  

Be aware of the strong twisting forces 

produced by the Auger during operation.

12. During drilling, periodically pull Auger up to remove 

loosened earth. If loosened earth is allowed to 

remain in the drilled hole, the Auger will screw 

into the earth, become stuck, and twist violently.

NOTICE:

 If Auger becomes stuck, dig bit out.

Do not rock auger to loosen bit. Bit will bend. 
13. Release the Throttle as soon as the drilling 

is completed, allowing the Engine to idle.

NOTICE:

  Avoid running the Auger at 

full throttle without a drilling load. 
14. After running the Auger for an extended period of 

time, allow the Engine to idle for several minutes to 

dissipate the heat.  This will prevent some Engine 

parts (ignition system, piston rings, carburetor, etc.) 

from being damaged by overheating.  

15. Press the Power Switch to O to turn off the Engine. 
16. Clean, then store the tool in a clean, dry, 

safe location out of reach of children 

and other unauthorized people.

NOTICE

See Long-Term Storage on page 15 

for complete storage instructions.

Summary of Contents for 63022

























Reviews: