background image

Page 3

For technical questions, please call 1-888-866-5797.

ITEM 69727 
        

S

AFETY

S

ETU

p

Op

ERA

TION

M

AINTENANCE

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol.  It is used to alert you to potential 

personal injury hazards.  Obey all safety messages that 

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,  

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Symbol Definitions

Symbol

property or Statement

RpM

Revolutions Per Minute

Hp

Horsepower

WARNING marking concerning 
Risk of Eye Injury.  Wear ANSI-approved 
safety goggles with side shields.

Read the manual before 
set-up and/or use.

WARNING marking concerning 
Risk of Hearing Loss.  
Wear hearing protection.

Symbol

property or Statement

WARNING marking concerning 
Risk of Respiratory Injury.  

Operate engine OUTSIDE and far away 

from windows, doors, and vents.
WARNING marking concerning 
Risk of Fire while handling fuel.  
Do not smoke while handling fuel.
WARNING marking concerning 
Risk of Fire.   
Do not refuel while operating. 
Keep flammable objects 
away from engine.

IMpORTANT SAFETY INSTRUCTIONS

 SAVE THESE INSTRUCTIONS –  

This manual contains important instructions that should be followed 
during installation and maintenance of the generator and any batteries.

Summary of Contents for 61563

























Reviews: