Precor EFX 813 Assembling And Maintaining Manual Download

Page: 5 / 68

Important Safety Instructions

Important:

Save these instructions for future reference.

Read all instructions in the documentation provided with your

exercise equipment, including all assembly guides, user

guides, and owner’s manuals, before installation of this

device.

Note:

This product is intended for commercial use.

The display apparatus (hereinafter referred to as the

console

)

is intended to be shipped with new Precor exercise equipment

(hereinafter referred to as the

base unit

). It is not packaged for

individual sale.

WARNING

To prevent injury, the console must be

attached securely to the base unit following all

assembly and installation instructions shipped

with the base unit. The console is intended to

be connected to AC mains power through the

furnished power supply ONLY. It should be

powered on only when installed as described

in the assembly and installation instructions

shipped with the base unit. The console is

intended for use only with Precor fitness

equipment, not as a standalone device.

Summary of Contents for EFX 813





































































Search results

Summary of Contents for EFX 813

Reviews:

Related manuals for EFX 813

Brands by name

Popular brands

Precor EFX 813, Assembling And Maintaining Manual

Search results

Summary of Contents for EFX 813

Reviews:

Related manuals for EFX 813

Brands by name

Popular brands