Precor EFX 813 Assembling And Maintaining Manual Download

Page: 12 / 68

Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833 / 813

Industry Canada

This device complies with RSS-210:2007 of the Spectrum

Management & Telecommunications Radio Standards

Specification. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference

received, including interference that may cause undesired

operation.
This Class A digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de la classe A est conforme à la norme

NMB-003 du Canada.

ATTENTION: Haute Tension

Débranchez avant de réparer

European Applications

CE compliance is claimed to the following directives:



1999/5/EC R&TTE Directive



2006/95/EC LVD Directive



2002/95/EC RoHS Directive

Directive compliance has been verified to the following

standards:



EN 55022



EN 300 330-1 V1.5.1



EN 300 330-2 V1.3.1



EN 301 489-3 V1.4.1



EN 301 489-1 V1.8.1



EN 60950-1

Summary of Contents for EFX 813





































































Search results

Summary of Contents for EFX 813

Reviews:

Related manuals for EFX 813

Brands by name

Popular brands

Precor EFX 813, Assembling And Maintaining Manual

Search results

Summary of Contents for EFX 813

Reviews:

Related manuals for EFX 813

Brands by name

Popular brands