Precision Rated Optics OLT-301 SERIES Operation Manual Download Page 4

 

888-545-1254 | www.PrecisionRatedOptics.com 

 

OLT-301 Series 

Safety Instructions 

Safety Terms Used in This Manual 

 

WARNING 

The WARNING sign denotes a hazard. It calls attention to a procedure which could result in personnel injury. 

 

CAUTION 

The CAUTION sign denotes a hazard. It calls attention to an operating procedure if not correctly performed or 
adhered to, could result in damage to or destruction of part or the entire product. 

 

NOTE 

The NOTE sign information that may be beneficial during the use and maintenance of the instrument. 

 

WARNING 

OLT-301 Series Optical Loss Tester is a laser device. User should always avoid direct eye exposure to the laser 
output. Using microscope or magnifier to observe the laser output should also be avoided: laser beam may 
converge on the retina and cause permanent eye injury. 

 

CAUTION 

Battery

: OLT-301 Series battery type is lithium battery. 

Battery Power Supply

: Do not expose battery to fire or intense heat. Do not open or mutilate battery. Avoid 

touching the electrolyte in the battery, which is corrosive and may cause injuries to eyes, skin or damage to 
clothes. 

External Power Supply

: OLT-301 Series support external power supply: 5V DC/750mA. External power supply 

is optional. 

Laser Radiation

: To avoid serious eye injury, never look directly into the optical outputs of fiber optic network 

equipment, test equipment. 

 

Always avoid looking directly into the optical output port, when the instrument is working. 

 

Always replace protective dust cap on the detector port when the instrument is not in use. 

 

Always avoid looking directly at unconnected end of optic fiber in testing and make the unconnected end 
pointing at a non-reflective object. 

 

 

Summary of Contents for OLT-301 SERIES





























Reviews: