Precision Digital Corporation PDA1500 Series Instruction Manual Download Page 9 | Manualshive

Page: 9 / 24

background image

Model PDA1500 Logic Level Converter

Instruction Manual

9

DIN Rail Mounting Instructions

DIN Rail Mounting Requirements



The converter requires a length of 35 mm “top hat” DIN rail 3.00" (76.3 mm)
wide.



The converter may be installed between other equipment on the same DIN
rail without removing the other equipment.



Clearance: allow at least 1.0" (25.4 mm) clearance above and below the
PDA1500 on the installation back-panel for wiring.

Snap-On Mounting Method

The converter may be snap-fit onto a DIN rail. The design of the
mounting tab allows for tool-free mounting.

WARNING

Hazardous voltages exist within enclosure and at
wiring connections. Installation and service should
be performed only by trained service personnel.

1. Hook the upper part of the converter onto the DIN rail at the

desired location.

2. Press the converter flat onto the DIN rail. The mounting tab will

snap into position, securing the converter.

«
...
7
8
9
10
11
...
»

Summary of Contents for PDA1500 Series

























Reviews:

No comments

Related manuals for PDA1500 Series

Brand: Rabbit Pages: 120

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 28

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 73

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 4

VLT AutomationDrive

Brand: Danfoss Pages: 89

Brand: INTECNO Pages: 16

Brand: V2 Pages: 48

Brand: ASEA Pages: 75

Brand: JRC Pages: 10

Brand: Ableconn Pages: 15

blueplanet 1502xi

Brand: Kaco Pages: 56

Brand: YASKAWA Pages: 120

Brand: Xuum Pages: 24

Brand: PRIZM Pages: 7

Brand: World Friendship Pages: 17

Brand: Weco Pages: 56

Brand: Hopewind Pages: 50

Brand: Dometic Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands