manualshive.com logo in svg

prana 150 ERP LITE, Technical-Operating Documentation

Share
Download
prana 150 ERP LITE Technical-Operating Documentation Download Page 9

9

1. Press the “Turn off” button on the remote 

control. Turn off the ventilation unit.

4. Remove the front 

part of the cover.

2. De-energize the ventilation unit.

6. Turn the mounting locks of the front cover 

and remove the back part of the cover.

8. Extract the heat exchanger and 

fans from the body.

3. Unscrew the 

screws on the 

cover.

7. Unscrew the self-tapping screws through 

special openings. Remove the fl ange.

MAINTENANCE

The maintenance consists in periodic (recommended 1-2 times a year) and preventive 

inspection of surfaces of the fans and the heat exchanger and, if necessary, in cleaning 

them. The procedure for disassembling / assembling the device for / after cleaning:

10. Remove the blades from the fan 

housings and clean them in a dry manner.

9. Unscrew the self-tapping screws. 

Remove the fans on both sides.

5. Unscrew the screws on the 

connector and disconnect the wires.

Summary of Contents for 150 ERP LITE













Reviews:

No comments

Brands by name

Popular brands

Load more brands