manualshive.com logo in svg

Pramac LUCE MCPH P7, User Manual, Page: 15 / 30

Share
Download
Pramac LUCE MCPH P7 User Manual Download Page 15

ENGLISH 15

 

 

4.

 

Lean

 

the

 

module

 

on

 

the

 

frame

 

making

 

the

 

module

 

slide

 

behind

 

the

 

clamps.

 

 

                      

 
 
 
 
 
 
 

5.

 

Proceed

 

adding

 

the

 

upper

 

clamps

 

and

 

the

 

lateral

 

fixing

 

bar.

 

Finally

 

fix

 

up

 

firmly

 

all

 

the

 

clamps.

 

Vertical

 

fixing

 

bars

 

are

 

fixed

 

on

 

the

 

frame

 

in

 

3

 

points.

 

 

NOTE:

 

Tighten

 

the

 

screws

 

with

 

the

 

torque

 

provided

 

by

 

the

 

manufacturer

 

for

 

the

     

hardware

 

used.

 

Pramac

 

recommend

 

bolts

 

and

 

nuts

 

with

 

guaranteed

 

mechanical

 

characteristics,

 

with

 

a

 

bolt/nut

 

friction

 

factor

 

constant

 

and

 

known.

 

Ex:

   

Bolts

 

M8

 ‐ 

Class

 

4.8

 

–

 

factor

 

0.20

 → 

fric on

 

torque

 

=

 

14.3

 

Nm

 

 

 
 

 

 

 

photovoltaikforum.com

Summary of Contents for LUCE MCPH P7































Reviews:

No comments