background image

3

3

0000

PASSW.

Txt 1

0000
9999

NO

ADV.SET

Txt 2

NO

YES

1 2

1 2

*1

10.4 mA

%

40.0

YES

ADV.SET

Txt 2

NO

YES

1 2

CURR

IN TYPE

Txt 3

VOLT
CURR

1 2

3

3

3

3

3

*0

4-20

I.RANGE

Txt 4

-/+20

-/+10

0-20
4-20

1 2

3

0-10

V.RANGE

Txt 5

1 2

12

VOLT

CURR

3

-/+10

-/+5

-/+1
2-10
0-10

1-5

0-5

0.2-1

0-1

@C 

@F 

bar 

cm 

ft 

ft/h 

ft/min 

ft/s 

gal/h 

gal/min 

GW 

hp 

hPa 

Hz 

in 

in/h 

in/min 

in/s 

ips 

kA 

kg 

kJ 

kPa 

kV 

kW 

kWh 

l/h 

l/min 

l/s 

m/h 

m/min 

m/s 

m/s2 

m3 

m3/h 

m3/min 

mA 

mbar 

mils 

min 

mm 

mm/s 

mol 

Mpa 

mV 

MW 

MWh 

Ohm 

Pa 

pH 

rpm 

t/h 

uA 

um 

uS 

Wh 

yd 

[blank]

UNIT

mA

Txt 6

[blank]

:
:

%

@F
@C

(69 units)

1 2

11.11

DEC.P

Txt 7

111.1
11.11
1.111

1111

1 2

VOLT

IN TYPE

Txt 3

3

18 4104V102-UK

Routing diagram

If no key is activated for 1 minute, the display will return to the default state 1.0 without saving configuration changes. 

1

 Increase value / choose next parameter

2

 Decrease value / choose previous parameter

3

 Save the chosen value and proceed to the next menu

Hold 

3

 Back to previous menu / return to menu 1.0 without saving.

Continued on the page
Routing diagram ADV.SET

*0

Default state.

Line 1 shows the scaled process value - OK or error. 

Line 2 shows the selected engineering unit.

Line 3 shows analogue output or TAG no.

Line 4 shows status for communication and signal trending.

*1

Only displayed if password is enabled.

Power up

1

 and 

2

 held:  

Toggle line 3 function 
A.Out / TAG.
(Setting is volatile - use 
DISP setup menu to 
change and store line 3 
function).

Correct 

No

Yes

Correct 

No

Yes

Selectable

 UNITS:

Continued on 

the next page

Summary of Contents for 4104


























Reviews: