background image

8

WARNING 

- Before performing maintenance or making adjustments, switch off the machine and disconnect the 

battery.

* If the fuse blows several times, the machine should be checked by an authorised Service Agent

Troubleshooting

Problem:

Possible Cause:

Solution is not being 
picked up

Vacuum motor is not running
Water filter is clogged
Recovery tank is full
Squeegee or vacuum hose is clogged, broken or disconnected
Bad seal at tank cover, vacuum motor or squeegee
Worn or misaligned squeegee blades.
Incorrect squeegee pressure.
Squeegee swing arm mechanism not functioning properly

Squeegee is leaving 
streaks

Debris is on blade
Blades are torn or damaged
Floors not properly swept before cleaning

Solution is not feeding or 
turning off properly

Clogging of hose or valve

Batteries are not 
holding a charge

Batteries need to be replaced
High current draw from high brush pressure
Charger needs servicing
Battery is run down

Floors are not being 
scrubbed, stripped or 
buffed properly

Brush motor not working
Excessive pad or brush wear
Going too fast over dirty spots
Inadequate solution feed
Inadequate cleaning procedure

Summary of Contents for PAS20BA-BC










Reviews: