Powerware 1085 Series Installation Manual Download Page 17 | Manualshive

Page: 17 / 54

background image

11

Powerware 9350 Series 685 and 1085 Auxiliary Battery Cabinets

Installation Manual

164201408 Rev. P00 053002

Connecting to Powerware 9350 30---160

The method you use to install your battery cabinets depends on which

UPS you have. For the purpose of discussion, this chapter uses the term

UPS

to refer to the UPS cabinet, and the term

battery cabinet

to refer to any battery

cabinet. There are two different sizes of battery cabinets, but the procedure for

connecting the cabinets to your UPS system is the same.

•

Joining one or more battery cabinets to the UPS

•

One or more battery cabinets separately located from the UPS.

The Powerware 9350 UPS with Integral Battery Cabinets

Use this procedure to attach a Powerware 9350 Series 685 or Series 1085 Battery

Cabinet to any Powerware 9350 UPS cabinet (see Figure 6).

Figure 6. UPS with Integral Battery Cabinet

«
...
15
16
17
18
19
...
»

Summary of Contents for 1085 Series























































Reviews:

No comments

Related manuals for 1085 Series

Brand: Laser Pages: 8

Brand: F.F. Group Pages: 44

Brand: M/A-Com Pages: 38

Brand: Parkside Pages: 64

Brand: Parkside Pages: 44

Brand: Parkside Pages: 64

Brand: Fein Pages: 152

Brand: M-system Pages: 3

Brand: Ransburg Pages: 40

Brand: Mitox Pages: 40

Brand: Agilent Technologies Pages: 47

Brand: Laguna Tools Pages: 9

Brand: Senco Pages: 46

Brand: Gardena Pages: 14

Brand: Eastwood Pages: 3

Brand: Larson Electronics Pages: 2

Brand: RED ROOSTER Pages: 8

KH 3036 LITHIUM ION CORDLESS SCREWDRIVER

Brand: Parkside Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands