background image

 

23 

 

EN 

5. Storage and Maintenance 

5-1. Storage   

Before storing, charge the UPS at least 7 hours. Store the UPS covered and upright in a cool, dry 
location. During storage, recharge the battery in accordance with the following table: 

Storage Temperature 

Recharge Frequency 

Charging Duration 

-25°C - 40°C 

Every 3 months 

1-2 hours 

40°C - 45°C 

Every 2 months 

1-2 hours 

5-2. Maintenance   

  The UPS system operates with hazardous voltages. Repairs may be carried out only by qualified 

maintenance personnel.   

  Even after the unit is disconnected from the mains, components inside the UPS system are still 

connected to the battery packs which are potentially dangerous.   

  Before carrying out any kind of service and/or maintenance, disconnect the batteries and verify that 

no current is present and no hazardous voltage exists in the terminals of high capability capacitor such as 
BUS-capacitors.   

  Only persons are adequately familiar with batteries and with the required precautionary measures 

may replace batteries and supervise operations. Unauthorized persons must be kept well away from the 
batteries.   

  Verify that no voltage between the battery terminals and the ground is present before maintenance 

or repair. In this product, the battery circuit is not isolated from the input voltage. Hazardous voltages may 
occur between the battery terminals and the ground.   

  Batteries may cause electric shock and have a high short-circuit current. Please remove all 

wristwatches, rings and other metal personal objects before maintenance or repair, and only use tools 
with insulated grips and handles for maintaining or repairing. 

  When replace the batteries, install the same number and same type of batteries.   

  Do not attempt to dispose of batteries by burning them. This could cause battery explosion. The 

batteries must be rightly deposed according to local regulation. 

  Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and eyes. It may 

be toxic.   

  Please replace the fuse only with the same type and amperage in order to avoid fire hazards.   

  Do not disassemble the UPS system. 

 

Summary of Contents for VFI 10000CRM LCD




























Reviews: