Powermate LiftGate LG-3 Installation & Operation Manual Download Page 34

Page: 34 / 40

DETAIL A

PowerMate

LiftGate™

Installation & Operation Manual

CRADLE ATTACHMENT INSTALLATION

Step 1. Extend unit approximately 24 inches. Insert the two 1/4-20NC slab sided head

Bolts into the holes provided in the Outer Frame, engaging the heads into the
extruded channels. Hang the Cradle Attachment on the bolts and retain with
two 1/4-20NC Lock Nuts.

Step 2. Using the bottom center hole in the Cradle Attachment as a guide, drill a

9/32"hole through the Outer Frame. CAREFULL! Take care not to hit the
Actuator Inner Tube when breaking through.

Step 3. Insert a 1/4-20NC x 3/4"Bolt from the Cradle side and secure the Attachment

with 1/4-20NC Lock Nut.

Cradle Attachment Lefthand PN 480060
Cradle Attachment Righthand PN 480065

-Righthand unit shown.

-Strap removed for clarity.

Outer Frame

Cradle Attachment

1/4-20NC x 3/4"Bolt

9/32"Hole

1/4-20NC Lock Nut

PN 018790 Rev.D2

Eng. 01/ 10/ 13

1/4-20NC Lock Nut

Slabbed sides of 1/4-20NC Special

Bolts fit into the extruded channels

in the Outer Frame. -2 places.

7.01

Summary of Contents for LiftGate LG-3









































Search results

Summary of Contents for LiftGate LG-3

Reviews:

Related manuals for LiftGate LG-3

Brands by name

Popular brands

Powermate LiftGate LG-3, Installation & Operation Manual

Search results

Summary of Contents for LiftGate LG-3

Reviews:

Related manuals for LiftGate LG-3

Brands by name

Popular brands