manualshive.com logo in svg

PowerBass BTA-8, Application Manual, Page: 8 / 20

Share
Download
PowerBass BTA-8 Application Manual Download Page 8

14.5" (368mm)

21.5" (546mm)

10" (254mm)

ENCLOSURE DIMENSIONS AND SPECIFICATIONS

NOTE:

 The speaker system should be secured to  protect the enclosure from moving. Before final 

mounting, be sure to check the sound one last time and  make sure the enclosure is properly 
placed to produce the desired bass output. Use the two mounting straps provided and wrap them 
around the enclosure as shown in the drawing above-a strap should be placed on each side of the 
embroidered PowerBass logo to be most effective. Next secure the enclosure by screwing through 
the strap with the self-tapping screws provided, then tighten the straps.
 
When mounting in a trunk, try to make sure the enclosure is positioned in a manner that packages 
and luggage will not slide and hit the protective woofer grill.
 
In some cases where there is no flat or even mounting area, it may be necessary to use a wooden 
board to fasten the enclosure to and properly secure the mounting straps. 

Mounting Straps

Summary of Contents for BTA-8





















Reviews:

No comments