background image

N8417pr-0920

PROBLEMS AND SOLUTIONS GUIDE

Q

Short run time (Less than  

Undercharged battery 

Charge the battery. A new battery should have been

1 - 3 hours per charge) 

 

charged for at least 18 hours before using the vehicle for

 

 

the first time. After first-time use, recharge the battery for

 

 

at least 14 hours after each use. Never charge the

 

 

battery longer than 30 hours.

 

 

Check all wires and connectors. Make sure the motor

 

 

harness connector is tightly plugged into the battery, and    

 

 

that the charger is plugged into the wall. 

 

 

Make sure power flow to the wall outlet is “ON”.

 

Overcharged battery 

Do not charge the battery longer than 30 hours. If you 

 

 

suspect that your battery is damaged as a result of 

 

 

overcharging, contact your local Power Wheels

®

 authorized  

 

 

service center. They can test the battery for you.

 

Battery is old and will not 

Even with proper care, a rechargeable battery does not 

 

accept full charge 

 last forever. Average battery life is 1 to 3 years depending 
on vehicle use and use conditions. Replace only with a
Power Wheels

®

 12 Volt Lead-Acid Rechargeable Battery. 

Do not substitute parts.

 

Tripped thermal fuse 

  The built-in thermal fuse may "trip" and shut down 
operation of the vehicle if the vehicle is overloaded or the 
driving conditions too severe. Once a fuse has "tripped", 
remove your foot from the pedal and wait approximately 
25 seconds before operating the vehicle again. To avoid 
repeated automatic shutdowns, do not overload the vehicle 
by exceeding the 130 lbs maximum weight capacity or by 
towing anything behind the vehicle. Do not drive up hills or 
run into fixed objects, which can cause the wheels to stop 
spinning while power is still being supplied to the motors.
If a thermal fuse continually trips, contact your local
Power Wheels

®

 authorized service center.

 

PROBLEM

 

POSSIBLE CAUSE

 

SOLUTION

Vehicle runs sluggishly 

Undercharged battery 

Charge the battery. A new battery should have been

 

 

charged for at least 18 hours before using the vehicle for

 

 

the first time. After first-time use, recharge the battery for    

 

 

at least 14 hours after each use. Never charge the battery  

 

 

longer than 30 hours. 

 

 

Check all connectors. Make sure the charger connector    

 

 

is tightly plugged into the battery, and that the charger is 

 

 

plugged into the wall.

 

 

Make sure power flow to the wall outlet is “ON”. 

 

Battery needs charging 

Be sure to charge the battery after each use.

 

Battery is old and will not  

Even with proper care, a rechargeable battery does not

 

accept full charge 

 last forever. Average battery life is 1 to 3 years depending 
on vehicle use and use conditions. Replace only with a
Power Wheels

®

 12 Volt Lead-Acid Rechargeable Battery. 

Do not substitute parts.

 

Vehicle is overloaded 

Make sure you do not overload the vehicle by allowing

 

 

more than two riders at one time, exceeding the 130 lbs.

 

 

maximum weight capacity, or by towing objects behind the

 

 

vehicle. If the vehicle is overloaded, the built-in thermal fuse in  

 

 

the battery may "trip", and automatically shut down operation   

 

 

for approximately 25 seconds. Adjust the driving conditions

 

 

to prevent repeated automatic shutdowns. 

 

Driving conditions are too stressful 

Use only on generally level ground.

N8417pr-0920

30

Meijer.com

Summary of Contents for CADILLAC ESCALADE CUSTOM EDITION N8417

































Reviews: