background image

17

N8417pr-0920

ASSEMBLY

F

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can 
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types: 

alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove 

exhausted batteries from the product. Dispose of batteries safely. 
Do not dispose of product in a fire. The batteries may explode
or leak.

• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,

as recommended.

• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be 

charged under adult supervision. 

1.5V x 4

"C" (LR14)

• Locate the FM Radio on the dash.
• Loosen both screws in the battery compartment door.
• Remove the battery compartment door.
•  Insert four, new "C" (LR14) alkaline batteries.

Hint:

 We recommend using 

alkaline

 batteries for longer

battery life.

• Replace the battery compartment door and tighten the screws.
• When sounds become faint or stop, it’s time for an adult to 

change the batteries! Please refer to page 26 for FM Radio use.

Loosen This Screw

29

• Fit the long tabs on the hood into the slots in the front end of

the vehicle.

Hood

FRONT VIEW

• Lower and fit the side tabs on the hood into the slots on each 

side of the front end of the vehicle.

Hood

Tab

Slot

30

Meijer.com

Summary of Contents for CADILLAC ESCALADE CUSTOM EDITION N8417

































Reviews: