background image

D O W N L O A D

 

THE C-MONSTER APP @

MAINTENANCE

 

and Storage

• Inspect all hydraulic lines for kinking or abrasion prior to use.
• Inspect all hydraulic fittings for leaks and proper tightness prior to each use.

CAUTION:

  

If disconnecting the hydraulic lines, please read the following:

 

Hydraulic lines are always pressurized and disconnecting them will cause 
a sudden high pressure release. This high pressure release may cause oil 
leakage from the lines and/or fittings. When depressurizing the lines the 
unit must be supported otherwise the anchor will fall to the fully deployed 
position. This may result in damage to the unit as well as bodily harm.

• Inspect all electrical connections to ensure that they are secure and free of corrosion 

every 3 months.

• Inspect all fasteners for proper tightness after every 100 cycles to ensure that 

the Power-Pole anchor is in safe working condition.

NOTE:

  

Tighten the 2 lower stern bracket lock nuts snug and all other lock nuts 
flush with the end of bolt with no threads showing. 

FIG. 1 & 2

IMPORTANT:

  

The stern bracket hinge bolts on the 10’ Blade model do not 
require retightening. 

•  Ensure that the Green Marine

®

 biodegradable hydraulic fluid level is within 

the indicator marks on the reservoir at all times.

C-MONSTER 

Smart Phone App

Figure 1

Figure 2

The C-Monster App is available for free from Google Play and the Apple App 
Store. The C-Monster App allows you to do the following:

• 

Configure settings for custom operation.

 Take full control 

of everything from deployment speed to independent or synchronized 
control of multiple anchors. Not to mention Auto Up/Auto Down 
and bottom sensing.

• 

Troubleshoot with AMP streaming instant diagnosis. 

The information is sent directly to the Power-Pole Technical Support  
Team so we can instantly see what’s happening and you can count 
on little or no down time.

• 

Check signal strength of all your remotes with 

RSSI evaluation.

 

This allows you to instantly see if your signal is weak or if any other devices 
are disrupting your signal. 

 Update software.

 You will recieve automatic prompts to update your 

C-Monster software if a new version is available.

• Quick product registration.

 Now you can easily register your Power-Pole 

anchors and accessories directly through the app. 

• Theft recovery.

 Once you register your Power-Pole anchor with the C-Monster App, 

if it’s ever stolen we can help law enforcement track and recover it.

Summary of Contents for Blade





















Reviews: