background image

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
EYE, EAR & LUNG PROTECTION 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

This instruction manual includes the following: 

 

General Safety Rules 

 

Specific Safety Rules and Symbols 

 

Functional Description 

 

Assembly 

 

Operation 

 

Maintenance 

 

Accessories 

 

 

 
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CSA 
REQUIREMENTS or ANSI SAFETY STANDARD Z87.1

 

 
FLYING DEBRIS can cause permanent eye damage. Prescription 
eyeglasses ARE NOT a replacement for proper eye protection. 

 

WARNING:

 

Non-compliant eyewear can cause serious injury if 

broken during the operation of a power tool.

 

 

 

SAVE THESE INSTRUCTIONS FOR REFERENCE 

 

WARNING:

 Use hearing protection, particularly during extended 

periods of operation of the tool, or if the operation is noisy. 

 

 

GENERAL SAFETY WARNINGS 

           

 

         WARNING:

 

Before using this tool or any of its accessories, read this 

manual and follow all Safety Rules and Operating Instructions. The important 
precautions, safeguards and instructions appearing in this manual are not 
meant to cover all possible situations. It must be understood that common 
sense and caution are factors which cannot be built into the product. 

 

 

Summary of Contents for JD3103U






















Reviews: