Power Electronics NB CITY Hardware And Installation Manual Download Page 4

Page: 4 / 48

NB City

POWER ELECTRONICS

ABOUT THIS MANUAL

ABOUT THIS MANUAL

PURPOSE

This manual contains important instructions for the installation, configuration and use of NB City electric

vehicle charging post. From now on, this manual refers to NB City with the term "charger" or

“equipment”.

Power Electronics reserves the right to modify product features.

TARGET AUDIENCE

This manual is intended for qualified customers who will install, operate and maintain Power Electronics

NB City electric vehicle charging post.

Only qualified technical personnel validated by Power Electronics may install and commission the

chargers.

REFERENCE MANUALS

The following reference documents are available for NB City electrical vehicles charging solutions:

•

NB App User’s manual

POWER ELECTRONICS CONTACT INFORMATION

Power Electronics USA Inc.

1510 N. Hobson Street, Gilbert,

Phoenix

AZ 85233

UNITED STATES OF AMERICA

US Sales: 602-354-4890 / (480) 519-5977

Fax: (415) 874-3001

Power Electronics España, S.L.

Polígono Industrial Carrases

Ronda del Camp d’Aviació nº 4

46160, Llíria (Valencia)

SPAIN

Tel: (+34) 961 366 557 / Fax: (+34) 961 318 201

Website:

www.power-electronics.com

Summary of Contents for NB CITY

















































Search results

Summary of Contents for NB CITY

Reviews:

Related manuals for NB CITY

Brands by name

Popular brands

Power Electronics NB CITY, Hardware And Installation Manual

Search results

Summary of Contents for NB CITY

Reviews:

Related manuals for NB CITY

Brands by name

Popular brands