UK Help Line: 0870 - 7323023 / IRELAND Help Line: 1800-481005 - Powercraft
7
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting wrenches are removed from the
tool before turning it on.
17. Avoid unintentional starting.
Do not carry plugged-in tools with finger on switch. Be sure switch is off when plugging in.
18. Outdoor use extension cords.
When tool is used outdoors, use only extension cords intended for use outdoors. Always
use tools in conjunction with a residual circuit breaker device.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate power tools when you are
tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. Aguard or other part that is damaged should be
properly repaired or replaced by an authorised service centre unless otherwise indicated
elsewhere in this instruction manual. Have defective switches replaced by an authorised
centre. Do not use tool if switch does not turn on and off.
21. Warning.
The use of any other accessory or attachment other than recommended in this operation
manual or the catalogue may present a risk of personal injury.
22. Have your tool repaired by an expert.
This electric tool complies with the relevant safety regulations. Repairs may only be made
by a qualified electrician using original spare parts; otherwise, the user may be subject to
accidents.
23. Hearing protection should be worn.
Special safety instructions
Wear ear and eye protection
•
Check that the maximum speed indicated on the grinding disc corresponds to the
maximum speed of the machine. The speed of the machine must not exceed the value on
the grinding disc.
•
Make sure that the dimensions of the grinding disc correspond to the specifications of the
machine.
•
Make sure that the grinding disc has been mounted and fastened properly. Do not use
reducing rings or adapters to make the grinding disc fit properly.
•
Treat and store grinding discs in conformance with the supplier’s instructions.
•
Do not use the machine for grinding workpieces with a maximum thickness exceeding the
maximum grinding depth of the grinding disc.
•
Do not use grinding discs for deburring.
•
When grinding discs have to be mounted on the thread of the spindle, make sure that the
spindle has sufficient thread. Make sure that the spindle is sufficiently protected and does
not touch the grinding surface.
GB
10
UK Help Line: 0870 - 7323023 / IRELAND Help Line: 1800-481005 - Powercraft
•
Clamp the workpiece and make sure that the workpiece cannot slide from under the
machine during the grinding activities.
•
When working with the machine, always hold it firmly with both hands and provide for a
secure stance.
•
Always direct the cable to the rear away from the machine.
•
Insert the mains plug only when the machine is switched off.
•
Apply the machine to the workpiece only when switched on
Never use the machine for grinding magnesium workpieces.
The ON/OFF switch
Fig. A
Switch the machine on by pressing the trigger switch (1). When you release the trigger switch
the machine will turn off.
Switch-lock
You can lock the ON/OFF switch by pressing the trigger switch (1) and then pressing the switch
lock (6). Release the switch-lock by pressing the trigger switch (1) quickly.
Do not put the machine down when the motor is still running.
Roughing
Fig. F
•
Hold the machine firmly and move it against the workpiece. Move the grinding disc evenly
across the workpiece.
•
During roughing hold the machine at an angle of 30º - 40º across the workpiece.
Never use grinding discs for roughing!
Grinding
Fig. G
•
The machine must always be moved in the opposite direction to the direction of rotation.
Therefore, never move the machine in the other direction! Otherwise, the danger exists of it
being pushed uncontrolled across the workpiece.
•
Inspect the grinding disc regularly. Worn discs have a negative effect on the efficiency of
the machine. Replace the grinding disc before it wears out.
•
Do not put the machine down when the motor is still running. Do not place the machine on a
dusty surface. Dust particles may enter the mechanism.
•
Always switch off the machine first before removing the plug from the wall socket.
GB
